An electrostatic precipitator (ESP) with 5600 m2of collector plate area is 96 percent efficient inreating 185 m³/s of flue gas from a 200 MWthermal power plant. It was found that in order toachieve 97 percent efficiency, the collector platearea should be 6100 m2. In order to increase theefficiency to 99 percent, the ESP collector platearea (expressed in m2) would be

Answered: Image /qna-images/answer/1594bb3d-c767-4d69-b75d-222189dbf2e6.jpg

An electrostatic precipitator (ESP) with 5600 m? of collector plate area is 96 percent efficient in reating 185 m³/s of flue gas from a 200 MW nermal power plant. It was found that in order to chieve 97 percent efficiency, the collector plate rea should be 6100 m2. In order to increase the efficiency to 99 percent, the ESP collector plate area (expressed in m2) would be

An electrostatic precipitator (ESP) with 5600 m? of collector plate area is 96 percent efficient in reating 185 m³/s of flue gas from a 200 MW nermal power plant. It was found that in order to chieve 97 percent efficiency, the collector plate rea should be 6100 m2. In order to increase the efficiency to 99 percent, the ESP collector plate area (expressed in m2) would be

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter14: Ocean Thermal Energy Conversion And Ocean Salinity Gradient Energy

Section: Chapter Questions

Problem 15P

See similar textbooks

Similar questions

The following figure and table contains the water levels of the reservoirs in the system and the properties of the pipes.Calculate the current values in the pipes ignoring the local head losses (ν = 10-6 m.2nd/s). Energy slope linedraw
A hydroelectric power generating system is shown in the figure. Water flows from an upper reservoir to a lower one passing through a turbine at the rate of 187 liters per second. The total length of pipe connecting the two reservoirs is 143 m. The pipe diameter is 376 mm and the Hazen-Williams coefficient is 143. The water surface elevations of reservoirs 1 and 2 are 210 m and 68 m, respectively. Determine the power in kW required by the turbine if it is 79% efficient? Neglect minor losses. round your answers in 3 decimal places
PROBLEM 5: A turbine, located at an elevation 255 m below that of the water surface at intake, carries a flow of 3.5 m^3/s. The head loss in the pipeline leading to it is 10 m. Find the horsepower delivered by the turbine if its efficiency is 92%. (746 watts = 1 HP). Illustrate the problem and show your complete solution.
Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoirat elevation 70 m. The steel pipeline connecting the reservoirs has a nominal diameter of 1400mm (the actual inside diameter is 1372 mm) with C = 90. If the flow is 1.18 m3/s, the pumpingefficiency is 82%, and electricity costs $0.14/kWh. Assuming that the density of water is 1000kg/m3, what will be the monthly power bill? Sketch the hydraulic and energy grade lines.
5. Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoir at elevation 70 m. The steel pipeline connecting the reservoirs has a nominal diameter of 1400 mm (the actual inside diameter is 1372 mm) with C = 90. If the flow is 1.18 m3/s, the pumping efficiency is 82%, and electricity costs $0.14/kWh. Assuming that the density of water is 1000 kg/m3, what will be the monthly power bill? Sketch the hydraulic and energy grade lines.
A generating system consists of the following units:(A) 1 x 10 MW unit(B) 1 x 20 MW unit(C) 1 x 30 MW unit(D) 1 x 40 MW unitThe 10, 20 and 30 MW units have forced outage rates of0.08. The 40 MW unit has afull forced outage rate of0.08 and a 50% derated state which has a probability of0.06. (a) Calculate the LOLE for this system for a single daily peak load of 60 MW. (b) Whatis the LOLE for the same condition if the 40 MW unit is represented as a two-statemodel using an Equivalent Forced Outage Rate?
A circular channel of 1.2 m diameter is flowing half full. If the discharge in the channel is measured as 0.85 m3/s, calculate the Froude number of the flow and the specific energy.
A manufacturing facility consumes 40 m^3/h of water taken from a nearby river located 15 m below the factory tank.Calculate the daily pumping cost if water is conveyed through a 3in, 240 m-long pipe, including friction losses. The cost of electrical energy is 0.831 pesos/kilowatt-hour and the pump operates with 80% efficiency.
Compute the energy loss that would occur as 27 gal/min of water flows from a tank into a steel tube with an OD of 3.0 in and wall thickness of .025 in. The tube has a rounded inlet of radius (r) of .118 in.
A small coal-fired power plant sends 2.4 m3/s of flue gas through itselectrostatic precipitation (ESP). The particle migration velocity is knownto be 10 cm/s. Calculate the collection area if the overall ESP efficiency is95%.
Water is issued vertically at the rate of 30 liters per second through a 50mm diameter nozzle. Neglecting losses, how high above the nozzle tip can the water jet support a load of 250N?
From the test specifications given in Table 5.2(attached), show that thecompactive energy in method C is 2700 kN. m/m3.