An ideal air-standard Brayton cycle operating at steady state produces 10 MW of power. Operating data at principal states in the cycleare given in the table below. The states are numbered as in the figure below.State p(kPa) T (K) h (kJ/kg)11003003001200603.5610.531200145015744100780.3800Heat exchangercycleCompressorTurbineHeat exchangerQoutDetermine:(a) the mass flow rate of air, in kg/s.(b) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger.(c) the percent thermal efficiency.

Answered: Image /qna-images/answer/82c33289-43fd-4a5a-9132-d4883bd22a9d.jpg

An ideal air-standard Brayton cycle operating at steady state produces 10 MW of power. Operating data at principal states in the cycle are given in the table below. The states are numbered as in the figure below.

An ideal air-standard Brayton cycle operating at steady state produces 10 MW of power. Operating data at principal states in the cycle are given in the table below. The states are numbered as in the figure below.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below. The states are numbered as in Fig. 9.5 with p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, r = 15 and rc = 2. For n = 1.3, cv = 0.718 kJ/(kg-K), and cp = 1.005 kJ/(kg-K), a.) determine T2 in deg-C. b.) determine p2 in bar. c.) T4 in deg-C. d.) the mean effective pressure in kPa, for the modified cycle. e.) the heat transfer during heat addition process per unit mass in kJ/kg.
Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below. The states are numbered as in Fig. 9.5 with p1 = 100 kPa, T1 = 340 K, and T3 = 4850.3 K, r = 15 and rc = 2. For n = 1.3, cv = 0.718 kJ/(kg-K), and cp = 1.005 kJ/(kg-K), determine p2 in bar. determine T4 in deg-C. determine T2 in deg-C. determine the heat transfer during heat addition process per unit mass in kJ/kg.
13) An ideal air-standard Brayton cycle operating at steady state produces 50 MW of power. Operating data at principal states in the cycle are given in the table below. The states are numbered as in the figure below. Determine:(a) the mass flow rate of air, in kg/s.(b) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger.(c) the percent thermal efficiency.
Consider an air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below. Determine (a) the cutoff ratio. (b) the heat addition per unit mass, in kJ/kg. (c) the net work per unit mass, in kJ/kg. (d) the thermal efficiency.
1. In an ideal air-standard Otto cycle, the initial conditions are 1 bar and 300 K. The compression ratio is 12:1, and the maximum cycle temperature is 2500 K. Assuming cp = 1.004 kJ/kg-K & k = 1.4, find: (a) show the cycle in both P-v and T-s diagrams. Clearly label all states and energy transfers. (b) temperature at the end of compression, T₂ in K. (c) heat added during the combustion process in kJ/kg. (d) thermal efficiency of the cycle. (e) net work output from the cycle in kJ/kg.
For modeling a gas turbine power plant producing 10 MW of power, the ideal air-standard Brayton cycle operating at steady state is used. Operating data at principal states in the cycle are given in the table below. The states are numbered as in Fig. below. (a) Sketch the T–s diagram for the cycle and determine (b) the mass flow rate of air, in kg/s, (c) the rate of heat transfer, in kW, to the working fluid passing through the heat exchanger, (d) the thermal efficiency.
At the beginning of compression in an air-standard Diesel cycle, p1 = 96 kPa, V1 = 0.016 m3, and T1 = 290 K. The compression ratio is 15 and the maximum cycle temperature is 1290 K. Determine (a) the mass ofair, in kg. (b) the heat addition and heat rejection per cycle, each in kJ. (c) the net work, in kJ, and d) the thermal efficiency. (e) Solve the problem on a cold air-standard basis with constant specific heats.
In an air standard brayton cycle, air enters the compressor at 27 degree C and 100 kPa. The pressure ratio is 10, and the maximum allowable temperature is 1350 K. the compressor and turbine efficiencies are 85%, and pressure drops 27 kPa between the compressor discharge and turbine inlet. Determine the pressure and temperature at each state in the cycle, the compressor and turbine work, and the cycle thermal efficiency. Please show the PV and TS diagram. Please show complete formulas and solutions.
PART B ONLY A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve the problem below using the variable specific heat assumption. PART B - Determine the pressure ratio rp = P2/P1 and the temperature at the turbine exit, T4 (in K).
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use simplified standard cold air assumption method.
Q#01 An air-standard cycle consists of the following processes:(i) isentropic compression from 15C, 1.01 bar through a compression ratio of 5:1.(ii) heat addition at constant volume of 2600 kJ/kg.(iii) reversible adiabatic expansion to the initial volume.(iv) heat rejection isochorically.For air take R = 0.287 kJ/(kg·K) and cP = 1.005 kJ/(kg·K). Sketch the cycle on P-v andT-s diagrams, and calculate its ideal efficiency, mean effective pressure and peak pressure. Take the start of isentropic compression as state point 1.Now the cycle above is modified in two ways so the heat is added, i.e.,(a) isobarically, and(b) half isochorically and half isobarically.Take the start of isentropic compression in both the cases as state point 1. Compressionratio is increased so as to follow the same peak pressure as before. Now sketch these twocycles on both P-v and T-s diagrams, and calculate their ideal efficiencies and mean effective pressures. The values of R and cP remain the same.
2. An air-standard regenerative Brayton cycle operates at steady state and produces 10 MW of power. Given the pressures and temperatures at the various states in Table 1 below, determine: (a) the specific enthalpies (kJ/kg) at all states for which the values are not given, (b) the mass flow rate of air through the cycle in kg/s, (c) the rate of heat transfer (in kW) to the working fluid passing through the combustor, and (d) the thermal efficiency (%) of the cycle. (e) Sketch the cycle on a T-s diagram, showing all states and processes. Assume the compressor and turbine isentropic efficiencies are both 80% and that the regenerator effectiveness is 70%.