An ideal reheat Rankine cycle operates between the pressure limits of 20 kPa and 15 MPa, with reheat occurring at 3 MPa. The temperature of steam at the inlets of both turbines is 600°C, and the enthalpy of steam is 3027 kJ/kg at the exit of the high-pressure turbine, and 2385 kJ/kg at the exit of the low- pressure turbine. Disregarding the pump work, the cycle efficiency is O 30.0 % O 43.3 % O 35.2 % O 41.6 % O 40.0 %

An ideal reheat Rankine cycle operates between the pressure limits of 20 kPa and 15 MPa, with reheat occurring at 3 MPa. The temperature of steam at the inlets of both turbines is 600°C, and the enthalpy of steam is 3027 kJ/kg at the exit of the high-pressure turbine, and 2385 kJ/kg at the exit of the low- pressure turbine. Disregarding the pump work, the cycle efficiency is O 30.0 % O 43.3 % O 35.2 % O 41.6 % O 40.0 %

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal rankine cycle operates between the pressures 50 kPa and 7000 kPa. If the turbine outlet is maintained at 90% steam quality, calculate the thermal efficiency of the cycle.
An ideal Rankine cycle operates between the pressures of 50kPa and 7000kPa. If the turbine outlet is maintained at 90% steam quality, calculate the thermal efficiency of the cycle. a.0.3269 b.0.3229 c.0.3486 d.0.3473
In a Rankine cycle, the enthalpies at turbine entry and outlet are 3159 kJ/kg and 2187 kJ/kg. respectively If the specific purp work is 2 kJ/kg. What is the specific steam consumption (in kg/kWh) of the cycle based on net output ?
In a simple Rankine cycle, the working fluid is water, operating at pressures between 7.5 kPa and 1750 kPa. The water vapor is in the form of saturated steam at the turbine inlet. Recognizing that expansion in the turbine and compression in the pump are reversible adiabatic,a) Show the cycle schematically in the T-s diagram.b) Calculate the thermal efficiency of the cycle.
A simple ideal Brayton cycle is modified to incorporate multistage compression with intercooling, multistage expansion with reheating, and regeneration without changing the pressure limits of the cycle. As a result of these modifications, (a) Does the net work output increase, decrease, or remain the same? (b) Does the back work ratio increase, decrease, or remain the same?
35 - In the simple ideal Rankine cycle, the enthalpy of water at the pump outlet is 230 kJ/kg. If the pressure at the turbine inlet is 9 MPa and the temperature is 400ºC, which of the following should be supplied to the water at a flow rate of 50 kg/s? a) 225.5 MW B) 199.7 MW NS) 259.1 MW D) 224.8 MW TO) 144.4 MW
A Rankine Cycle operates at a throttle pressure and temperature of 5 MPa and 450°C, respectively. The generator produces 20 MW at an efficiency of 95% while the mechanical efficiency is 97%. The actual expansion efficiency of the turbine is 85% and the pressure of the condenser is 10 kPa. Determine the theoretical engine thermal efficiency in %.
An ideal Diesel cycle has a maximum cycle tempera¬ture of 2000°C. The state of the air at the beginning of the compression is P1 = 90 kPa and T1 = 15°C. This cycle is exe¬cuted in a four-stroke, eight-cylinder engine with a cylinder bore of 12 cm and a piston stroke of 14 cm. The minimum volume enclosed in the cylinder is 5 percent of the maximum cylinder volume. Determine the power produced by this engine when it is operated at 1500 rpm. Use constant specific heats at room temperature.
A simple ideal Brayton cycle is modified to incorporate multistage compression with intercooling, multistage expansion with reheating, and regeneration without changing the pressure limits of the cycle. As a result of these modifications, (a) Does the thermal efficiency increase, decrease, orremain the same? (b) Does the heat rejected increase, decrease, or remain thesame?
An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below, the conditions at the inlet to the first turbine stage are 1600 lbf/in.2, 1200°F and the steam is reheated to a temperature of T3 = 800°F between the turbine stages at a pressure of p3 = p2 = 200 lbf/in.2
A simple Rankine cycle operates between the pressure limits of 30 kPa and 4 MPa, with a turbine inlet temperature of 500°C. If the isentropic efficiency of the turbine is 70 percent, the turbine work output is
A simple ideal Brayton cycle operates with air with minimum and maximum temperatures of 27°C and 727°C. It is designed so that the maximum cycle pressure is 2000 kPa and the minimum cycle pressure is 100 kPa. Determine the net work produced per unit mass of air each time this cycle is executed and the cycle’s thermal efficiency. Use constant specific heats at room temperature