An infinite slope is to be constructed ina soil. The effective shear strengthparameters of the soil are c = 0 and0 = 30°. The saturated unit weight of theslope is 20 kN/m³ and the unit weightof water is 10 kN/m³. Assuming thatseepage is occurring parallel to theslope, the maximum slope angle for afactor of safety of 1.5 would be

Given data, Slope is infinite and seepage taking parallel to slope means water table is at top of…

An infinite slope is to be constructed in a soil. The effective shear strength parameters of the soil are c = 0 and = 30°. The saturated unit weight of the slope is 20 kN/m and the unit weight of water is 10 kN/m³. Assuming that seepage is occurring parallel to the slope, the maximum slope angle for a factor of safety of 1.5 would be

An infinite slope is to be constructed in a soil. The effective shear strength parameters of the soil are c = 0 and = 30°. The saturated unit weight of the slope is 20 kN/m and the unit weight of water is 10 kN/m³. Assuming that seepage is occurring parallel to the slope, the maximum slope angle for a factor of safety of 1.5 would be

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

Given an infinite slope with the following properties: γ = 17 kN/m3, H = 5 m, β = 34°, φ = 25° and c = 20 kPa. a. Determine the normal stress. b. Determine the shear stress. c. Determine the factor of safety.
3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface.
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
A long slope is made up of a cohesionless soil with the internal friction angle of 34°. If the water table rises to the surface of the slope, then determine the maximum possible value of the slope angle to get a factor of safety of 1.5. Take saturated unit weight as 18 kN/m3 and the unit weight of water as 10 kN/m3.
The soil of a infinitely long slope has cohesion of value 20 kPa and dry unit weight of 16 kN/m3. If the slope angle is 40° and has a critical height of 5 m, determine the angle of internal friction of the soil.
An infinite slope in purely cohesive soil has a saturated unit weight of 20 kN/m^3 and effective cohesion of 48 kPa. It has a slope of 18 degree. The clay has a depth of 5m over ledge rock. Depth of clay is measured vertically. 1. Determine the FS against slippage. 2. Determine the critical depth. 3. Compute for the stability number.