An intermediate beam is carried by a girder at its midspan. The intermediate beam has a dimension of 250mm x 450mm which carries a deadload of 29kN/m and a liveload of 10KN/m on its full span which is 3.9m long. On the otherhand the girder is supported by two columns, the girder has a dimension of 300mm x 500mm while the columns have a dimension of 450mm x 450mm. The girder carries a deadload of 39kN/m and a liveload of 20kN/m on its full span which is 4m long. If the girder has an effective depth of 490mm and the diameter of stirrups is 10mm, f'c = 27.6MPA, fy = 420MPA and fyt = 276MPA %3D

An intermediate beam is carried by a girder at its midspan. The intermediate beam has a dimension of 250mm x 450mm which carries a deadload of 29kN/m and a liveload of 10KN/m on its full span which is 3.9m long. On the otherhand the girder is supported by two columns, the girder has a dimension of 300mm x 500mm while the columns have a dimension of 450mm x 450mm. The girder carries a deadload of 39kN/m and a liveload of 20kN/m on its full span which is 4m long. If the girder has an effective depth of 490mm and the diameter of stirrups is 10mm, f'c = 27.6MPA, fy = 420MPA and fyt = 276MPA %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is loaded with a uniformly varying load O at point D and maximum of 7kN/m at the fixed support. Determine vertical reaction at the fixed support.
A horizontal steel girder of uniform section, 15 m long, is supported at its extremities and carries loads of 120 kN and 80 kN concentrated at points 3 m and 5 m from the two ends, respectively. I for the section of the girder is 1.67 x lO-3 m' and E = 200 GN/m2. Calculate the deflections of the girder at points under the two loads. (Cambridge)
For the following continuous beam, which is hinged connected at D, using the load combination 1.4G+1.6Q calculate: Maximum positive design moment at span BC (+Md,BC) Maximum negative design moment at support B (-Md,B) G=15 kN/m Q= 10 kN/m
A continuous beam ABC consists of spans AB and BC of lengths 4m and 6m respectively, the ends A and B being fixed. C is a free end. The span AB carries a uniformly distributed load of 24 kN/m while the span BC carries a point load of 108 kN at a distance of 2m from C. Find the support moments and support reactions
A 20 m long beam is simply supported at the left end and 5m from the right end. It is to be used as a bridge to carry a moving uniform highway load of 8 kN/m and a concentrated load of 12 kN. Compute the maximum span positive moment due to the highway loads. 0kN - m 460kN - m 350kN - m 225kN - m
A live load 0f 80 KN/m moves on a simply supported girder of span 12m. The maximum bending moment that can be occur at a section 4m from left end is
A beam ABCD is 14m long. It is supported at B. 4m from the left end A, and point D at the right end. It is subjected to a uniform live load of 30 kN/m and a concentrated load of 150 KN. If point C is 6 m from D. 1. What is the total length that the beam must be subjected to a uniform live load of 30 kN/m to obtain maximum positive shear at C? 2. What is the total length that the beam must be subjected to a uniform dead load of 20 kN/m to obtain maximum positive shear at C? 3. Compute the maximum positive shear due to the uniform dead load, live load, and concentrated load to obtain the maximum negative shear at C.
An I-beam is strengthened by bolting a plate to the top and bottom flange as shown. If the bolts are placed so that s = 180 mm, and each bolt can resist a maximum shear force of Vbolt = 27 kN, determine the largest shear force, V, to which the beam can be subjected. Express you answer in kN to the nearest whole kN.
Beam ABCD has a length of 14 meters, where points A nd D are located at theleftmost and rightmost end, while point C is located 10 meters from point A andpoint B is located midway between A and C. The beam is supported at A (hinged)and at C (roller). A concentrated load P is loaded at B and a uniform load "w" isapplied in the span(segment) CD. If P = 60 kN and w = 5 kN/m, compute the slopeat D in degrees
hree wheel loads roll as a unit across a 40ft. span. The loads are P1=4,000lbs and P2=6,000lbs separated by 9ft and P3=8,000lbs at 18ft from P2.Determine the maximum moment and maximum shear in the simply supported span.
A simple beam AB supports two connectedwheel loads 3P and 2P that are a distance d apart (seefigure). The wheels may be placed at any distancex from the left-hand support of the beam. (AssumeP =12 kN, d = 2 m, and L =15 m.)(a) Determine the distance x that will produce themaximum shear force in the beam, and alsodetermine the maximum shear force Vmax.(b) Determine the distance x that will produce themaximum bending moment in the beam, andalso draw the corresponding bending-momentdiagram.
A completely restrained beam having a span length of 4m with a uniformly distributed load of 60 kN/m from the midspan to the right support. Which of the following most nearly gives the moment at the right support in kN-m. Which of the following most nearly gives the reaction at the left support in kN. Which of the following most nearly gives the reaction at the right support in kN. Which of the following most nearly gives the maximum positive moment in kN-m.