An inward flow reaction turbine has external & internal diameters of & 1.5 m 0.8 m' respectively. The velocity of flow through runner is constant & is equal to 2 m/s. If the width of runner at inlet is 240 mm, then width at runner at outlet is more than inlet by A 200 mm В 210 mm C 450 mm D 128 mm

An inward flow reaction turbine has external & internal diameters of & 1.5 m 0.8 m' respectively. The velocity of flow through runner is constant & is equal to 2 m/s. If the width of runner at inlet is 240 mm, then width at runner at outlet is more than inlet by A 200 mm В 210 mm C 450 mm D 128 mm

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Related questions

Q: A water turbine operating at 85% efficiency is under a head of 100 m. If the constant discharge is…

Q: The component of Francis turbine which minimizes loss of kinetic energy at turbine outlet is a.…

A: Turbine: The mechanical device that always rotates and converts the energy that is taken from the…

Q: 33. An inward flow reaction turbine running at 450 rpm has an external diameter.of 50 cms and a…

Q: The ourlet pipe frrom a pump is a bend of 45° rising in the horizontal plane. The inlet and outlet…

Q: A pump draws 20 L/s of water from reservoir A to reservoir B. Assuming f = 0.013 for all pipes,…

A: Given:Q=20 L/s= 20*10-3 m3/sf=0.013L1=500 mL2=200 mmz1=15 mL2=1200 mD2=150 mmz2=60 m NOTE: According…

Q: the flow rate in each pipe (+ is out and - is into the reservoir) Assume hA = 60 m, hg = 90 m, hc =…

A: To given…

Q: Problem 2. At a hydroelectric power plant the flow is 3.25 meter cubed per second, the friction loss…

A: Given, Inlet flow = Qin = 3.25 m3/sFricition head loss in penstock = Hf = 15 mAvailable head = H =…

Q: (a) A pump draws water (50°F) from a reservoir, where the water-surface elevation is 520 ft and…

A: The overall pressure losses incurred by the fluid as it moves from the suction point to the…

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

A: Given: Q=200 lpsPB=690 kN/m2PA=206 kN/m2zA=67 mzB=30 mdA=300 mm = 0.3mdB=200 mm =0.2 m

Q: 1. A turbine is rated at 600 hp when the flow of water through it is 0.61 m/s. Assuming an…

Q: Q3: (A) A Pelton wheel has a bucket speed (u) of 12 m/s and is supplied with water at a rate of 0.68…

A: Note Question (A) is Solved here. For Question (B), Please post this Question again.

Q: 2. In this system, d = 6 in., D = 12 in., Azı = 6 ft, and Az2 = 12 ft. The discharge of water in the…

Q: For the siphon shown, use Bernoulli's equation to calculate the following. (Assume no friction or…

A: Here, the pressure asked are guage pressures. Dont take absolute pressure. The solution is provided…

Q: A large pipe with a cross-sectional area of 1.00 sq m descends 5.00 m and narrows to 0.500 sq m,…

Q: A pump draws water from a reservoir A(EL 0m) and lifts it to reservoir B(EL. 80m), the headloss are:…

A: Given data: Datum is located at point A Elevation of B = 80 m…

Q: A hydro turbine runs at 150 rpm, discharges 10 m3 /s under a net head of 30 m and maximum efficiency…

Q: Q5. Two tanks A and B of surface areas 600 m2 and 300 m2 are connected by an orifice of 0.18 m2 in…

Q: A centrifugal pump has vanes which are radial at the outer periphery. The impeller has an outer…

Q: Q6: A: A turbine is to operate under a head of 25m at 200 rpm. The discharge is 9 m³/s. if he…

Q: Q.3 Water flows through a 0.8m diameter pipe at the end of which there is a reducer connecting to a…

Q: 08. The turbine shown in Figure develops 2500 kW when the water flowrate is 20 m'/s. The head loss…

A: Given: Assume the diameter of the pipe as 2 m.

Q: Q2. A Pelton wheel has diameter of 4m and the average force of water against the blades is 13.13KN.…

Q: 31. The absolute velocity of water at inlet to a turbine is 12 metre/sec, the guide blade angle…

A: Given:-Absolute velocity of inlet of turbine=12m/sGuide blade angle=20°d=40cm=0.4mb=10cm=0.1mTo…

Q: A Pelton turbine with a 1.75 m impeller radius has a nozzle with a mouth diameter of 12 cm. Since…

Q: find the air flow through circular duct if the diameter(350mm) and velocity(6m/s) 0.013 m3/s O 0.33…

A: Since you have asked multiple questions in a single request we would be answering only the first…

Q: Water (Pwater = 1000 kg/m³) is supplied through a soft hose with diameter D = 75 mm, to a…

A: For solution refer below images.

Q: 3. A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per second.…

Q: An external gear pump running at 1140 rpm has an outer diameter 99 cm, inner diameter 424 mm and…

Q: H.W.: In the figure shown, the flow rate is 0.05 m/s, determine: (a) pressure at A and B, (b) the…

Q: A pipe of 400 mm diameter carries water at a velocity of 25m/s. The pressure at the points A and B…

A: The assumption in Bournalli's Principle 1) Flow is ideal 2) Flow is fully developed and laminar…

Q: 3) Given: Q = 14 lit/sec; For the suction pipe: diam. = 180mm with head loss = three times its %3D…

A: Given that, Volume flow rate, Q=14 lit/sec,Diameter of suction pipe, Ds=180 mm,Head loss of suction…

Q: A Francis turbine has the dimensions of ri=1.42 m, r2=2.00 m.bi=2.20 m and b2=0.731m. Rotation speed…

Q: H.W: The inlet diameter of the centrifugal pump, shown in figure below, is 28 in. and the outlet…

A: Given data, For centrifugal pump At inlet, d= 28 in Outlet mass flow rate is mo= 9200 lb/s…

Q: Q6. A pump moves water horizontally at a rate of 0.02m /s. Upstream of the pump where the pipe…

A: Given Data: Flow rate, Q=0.02 m3/s

Q: h h (а) (b)

Q: Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm…

A: For solution refer below images.

Q: A pump increases the pressure of water from 100 kPa to 900 kPa to an elevation of 35 m. The inlet…

A: Given data: Inlet pressure of water, Pin = 100 kPa. Outlet pressure of water, Pout = 900 kPa.…

Q: 18. A centrifugal pump has to work against a head of 25 metres at a speed of 850 rpm. The flow…

Q: A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of…

A: Given data: - The pipe diameter is d = 12 cm. The height of the hill is h = 60 m. The discharge at…

Q: If a fluid flows with 19.1 m/s velocity, then its kinetic head is equal to m

A: kinetic head is given by V2/ (2×g) here g= 9.81 m/s2.

Q: 6. Kaplan turbine of I m runner diameter working under a head of 50 m. If the whirl velocity at…

A: d=Runner Diameter=1 mH=Head=50 mVw1=Whirl Velocity at Inlet=19 m/su=Runner speed=46.47 rad/s

Q: 08. The turbine shown in Figure develops 2500 kW when the water flowrate is 20 m'/s. The head loss…

A: Power developed by the turbine, P=2500 kWWater flow rate, Q=20 m3/sTotal head loss, hL=2.5 m

Q: 2. In the figure shown, a liquid is pumped from reservoir A to tank B by a 12 hp pump having an…

Q: In this system, d = 6 in., D = 12 in., A-1 = 6 ft, and A=2 = 12 ft. The discharge of water in the…

Q: In case of Reciprocating pump if we know the actual discharge is 1.0796 x 10°m'/sec, time taken to…

A: Given data Actual discharge (Q) = 1.0796 x 10-3 m3/s Time (t) = 44 sec Head (h) = 19 cm = 0.19 m

Q: A pump draws water through a 20 cm suction pipe and discharges it through a 10 cm pipe in which the…

Q: Find the flow rate through the siphon and the pressure at the siphon apex. E.L. 130 m 물 -E.L. 120 m…

Q: H.W.: In the figure shown, the flow rate is 0.05 m/s, determine: (a) pressure at A and B, (b) the…

Q: Q2. A Pelton wheel has diameter of 4m and the average force of water against the blades is 13.13KN.…

Question

Q.1
An inward flow reaction turbine has
external & internal diameters of
&
1.5 m
0.8 m: respectively. The velocity of flow
through runner is constant & is equal to
2 m/s. If the width of runner at inlet is 240
mm, then width at runner at outlet is more
than inlet by
A 200 mm
В
210 mm
C
450 mm
D
128 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the speed ratio is 2.09 and the flow ratio is 0.68, and the overall efficiency is 60%. The diameter of the boss is 1/3 rd of the diameter of the runner . The discharge is ؟
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the speed ratio is 2.09 and the flow ratio is 0.68, and the overall efficiency is 60%. The diameter of the boss is 1/3 rd of the diameter of the runner . The diameter of the runner is *
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
A turbine of the Francis type operates with a head of 200 m and flow rate of 3 m3/s.The peak efficiency occurs at a head coefficient CH of 9, a flow coefficient CQ of 0.3, and apower coefficient CP of 2.5 (as defined in Section 12.7). Estimate the size of the machine,the maximum power produced, and the speed.
Acentrifugal pump has di = 24 cm, d2 = 36 cm, by = 12 cm, bz =7.5 cm, B1 = 22° and B2 = 38° and rotates at 1170 r/min. If the fluid is gasoline at 20°C and the flow enters the blades radially, estimate the theoretical (a) flow rate (b) horsepower, and (c) head. For gasoline, take p=680 kg/m3. R Gy Juald e
A hydroelectric plant has 14 identical Francis turbines, a gross head of 245 m, and a volume flow rate of 11.5 m3 /s through each turbine. The water is at 25°C. The efficiencies are ?turbine = 95.9%, ?generator = 94.2%, and ?other = 95.6%, where ?other accounts for all other mechanical energy losses. Estimate the electrical power production from this plant in MW
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
An existing impulse turbine-generator installation operates at 450 rpm under a net Head of 520 m. The output current is 60 cycles per second. If a single 18-cm diameter waterjet is used, Cv = 0.98, Øe = 0.45 and ηT = 0.85. Find the flow through turbine in m3/sec.
A piston PDP has a 5-in diameter and a 2-in stroke andoperates at 750 r/min with 92 percent volumetric effi ciency.(a) What is its delivery, in gal/min? (b) If the pump deliversSAE 10W oil at 20°C against a head of 50 ft, what horsepoweris required when the overall effi ciency is 84 percent?
A Kaplan turbine working under a head of 81 5 m is dis-charging 295 m%/sec. of water at 75 R.P.M. and developing 38,000B.H.P.The runner dia is 7 m and boss diameter is 3 m.Determine (2) the inlet and outlet blade angles of runner, (i)mechanical efficiency and (in) overall efficiency.Assume hydraulic efficiency as 94%