Q.3 Water flows through a 0.8m diameter pipe at the end of which there is a reducer connecting to a 0.6 m diameter pipe. If gauge pressure at the entrance to reduce is 400 KN/m- and velocity is 2m/sec. Determine the magnitude of thrust on reducer(KN) assuming that frictional head loss through reducer is 1m. A A 80 B 120 C 90 98

Q.3 Water flows through a 0.8m diameter pipe at the end of which there is a reducer connecting to a 0.6 m diameter pipe. If gauge pressure at the entrance to reduce is 400 KN/m- and velocity is 2m/sec. Determine the magnitude of thrust on reducer(KN) assuming that frictional head loss through reducer is 1m. A A 80 B 120 C 90 98

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
Two pressurized prismatic tanks A and B are connected at their sides by an orifice 140 mm in diameter. Tank A contains water at a depth of 3 m above the orifice and a pressure of 50 kPa on the water surface. Tank B also contains water at a depth of 2 m above the orifice and a pressure of 15kPa on the water surface. The coefficient of discharge is 0.86 and the coefficient of velocity is 0.92. Detemine the: show complete solution, thumbs up guaranteed 1. What is the the head lost in the orifice? 2. What is the value of power lost?
1) 2) Determine the Reynolds number in the pipe system and the significance of this Information? 3) Using Bernoulli’s equation, find the water pressure at point C? 4) Determine the head losses accumulated by the fluid when flowing in the pipeline? 5) Calculate the energy that the fluid will lose after passing through the turbine by applying theenergy equation? 6)If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? 7) Identify the most common water turbines and the limitations that exist within these differenttypes? 8) Although hydraulic turbines considered one of the most efficient power plants, theirecological impact is a big concern. Discuss this issue and suggest remedies for such problems by writing 100 words at least?
Water reservoir A (El. 13.5m) to reservoir B (El. 51.3) is lifted at the rate of 30000L/min. The intake pipe is 250mm. The discharge pipe is 200mm . Assuming the pipes are made of wrought iron, and the pump to be used runs at 1800 rpm, determine: a. the pump to be used; b. the number of stages to be used for the pump to operate at maximum efficiency.
Aa certain hydro-power station has a head of 500m between the upper and lower reservior. A. Determing the approach velocity of water as it enters the turbine ; B. If the volume flowrate is 60cumec, what is the diameter of the penstock; and C. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity approach and the corrected diameter of the penstock required
A certain hydro-power station has a head of 500m between the upper and lower reservoir . a. Determine the approach velocity of water as it enters the turbine; b. If the volume flow rate is 60 cumec, what is the diameter of the penstock; and c. If the head loss due to friction represents 10% of the static head in (a) determine the actual velocity of approach and the corrected diameter of the penstock required.
A centrifugal pump is used to pump water through horizontal distance of 150 meters and then raised to an overhead tank 20 meters above. The pipe is smooth with inside diameter of 50 millimeter. The pump head (meter of water) that will be generated at its exit to deliver water at a flow rate of 0.001 cubic meter per second is Blank 1 meter of water. Use fanning friction factor = 0.0062 Express your answers in whole siginificant figure without decimal value and without unit
Water flows from a lake through a 700-mm-long pipe having a diameter of 300 mmmm and a friction factor of f� = 0.025. The flow from the pipe passes through a 60-mmmm-diameter nozzle and is used to drive the Pelton wheel, where the bucket deflection angles are 150 ∘∘. Neglect minor losses. Determine the power produced when the wheel is turning under optimum conditions. Express your answer to three significant figures and include the appropriate units. Determine torque produced when the wheel is turning under optimum conditions. Express your answer to three significant figures and include the appropriate units.
The axial flow pump produces a discharge of 0.095 m3/sm3/s. (Figure 1) The impeller is rotating at ω� = 80 rad/srad/s, and it has a mean radius of 75 mmmm. The diameter of the impeller's shaft is 100 mmmm. Determine the angle α2�2, which the velocity of the water as it exits the blades V2�2 makes with its tangential component Vt2��2. Express your answer using three significant figures.
Water at 200∘F enters the radiator at A with an average velocity of 4 ft/s and a pressure of 60 psi. The copper pipe has a diameter of 14in. Take ε=5(10^−6)ft. The radiator is in the vertical plane. ρw = 1.869 slug/ft3 and νw=3.40(10^−6)ft2/s. Use the equation 1/√f = −1.8log[(ε/D/3.7)^1.11 +6.9/Re]. If each 180∘ bend has a minor loss coefficient of KL = 1.03, determine the pressure at the exit B
A centrifugal pump is used to pump water through horizontal distance of 150 meters and then raised to an overhead tank 20 meters above. The pipe is smooth with inside diameter of 50 millimeter. The pump head (meter of water) that will be generated at its exit to deliver water at a flow rate of 0.001 cubic meter per second is Blank 1 meter of water. Use fanning friction factor = 0.0062