A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of 60 m than the ground. The discharge at the end of the pipe is 200 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm?. Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id..) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe

A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of 60 m than the ground. The discharge at the end of the pipe is 200 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm?. Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id..) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Water is flowing through a pipe of 100 mm diameter under a pressure of 19.62 N/cm2 (gage) and with mean velocity of 3 m/s. find the total head of the water at a cross - section, which is 8 m above the datum line?
A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill at the height of 60 m above the ground. The flowrate at the end of the pipe is 180 lit/s. The pressure gauge is connected at the inlet of the pipe in the ground and measured as 35.5 N/cm2. Find the following: (i) The kinetic energy per unit weight at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe entry (unit in m)
Water flows through a 2.5 cm pipe at115 L/minand o.15 bar pressure. It vents vertically 1 mabove the pipe. How high will the water shootfrom the vent?
A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
An oil having viscosity 0.08 N S/m², Specific weight 8829 N/m, density 900 kg/m flow at the rate of 5410 m/sec through a horizontal circular pipe of 0.12 m diameter and length 150 m. Find, (a) Pressure difference in 150 m length in kN/m² (b)Wall shear stress in N/m² (c) Average, and maximum velocity.
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
A Pitot tube in a pipe in which air is flowing is connected to a manometer containing water asshown below. If the difference in water levels in the manometer is 10 cm, what is the velocity of flow in the pipe? Assume a tube coefficient of Cp = 0.99, specific weight of air is 12 N/ sq.m.
In an industrial cooling process, water is circulated through a system. If water is pump from the first floor through a 6cm diameter pipe with a speed of 0.45 m/s under a pressure of 400torr, what will be the pressure on the nest floor 4m above into a pipe with diameter 2cm? Show your solution
O.S. A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cv=0.95, Cv = 0.62 as shown in the figure. If the liquid is oil (s.g. = 0.85), what is the head, h in meter over the orifice is required? In Problem 1, determine the theoretical velocity of the jet Also in Problem 1, determine the theoretical flow (Ips).
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)