An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.

An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included angle of 40°, and density 1400kg/m 3 The angle of lap is 130° on the smaller wheel, the coefficient of friction is 0.4 and the maximum force allowed in the belt is 500N. Calculate the initial belt tension and reason for this.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
In a belt arrangement two pulleys are connected by flat belts having same diameters. Themaximum force on the tight side of belt is 662 N. If co-efficient of friction is 0.3 thenwhat is maximum force on the slack side of the belts?