Problem 4: Current MirrorTwo BJT transistors, both are operating in the forward active region, are used to produce the current IOUT through current mirroring of IBIAS. Assume that VA → ,Isı = Is2 = Is, and B1 = B2 = B for both transistors.VCCVcCIBIASRLOADIOUTQ2BJT Current MirrorYou may use LTspice simulation or hand calculation for this problem. Use the corresponding submission bin for this. If you opt to simulate, use the default NPN modelfrom LTspice.Analyze the circuit and answer the following:1. Which is the expression for IOUT?.OIOUT =B11-IBIASOIOUT =81IBIASOIOUT = IBIASB12BOIOUT = IBIASB122. If Vcc = 12 12, RLOAD = 1 kSN, IBIAS = 10.2 mA, and B = 100, what is the value of Vc1? Round to nearest volts. Note that if you are using LTspice tosimulate this problem, the default LTspice model for the NPN already suffice the given transistor properties.V

BJT current mirror circuit is used as a current regulator. It supply almost constant current to the…

Analyze the circuit and answer the following: 1. Which is the expression for IOUT?. OIOUT = B+1 IBIAS OIQUT = B1 BIAS B12 OIQUT = IBIAS OIOUT = B12 BIAS 2. If Vcc = 12 12, RLOAD = 1 kſN, IBIAS = 10.2 mA, and B = 100, what is the value of Vc1? Round to nearest volts. Note that if you are using LTspice to simulate this problem, the default LTspice model for the NPN already suffice the given transistor properties. V

Analyze the circuit and answer the following: 1. Which is the expression for IOUT?. OIOUT = B+1 IBIAS OIQUT = B1 BIAS B12 OIQUT = IBIAS OIOUT = B12 BIAS 2. If Vcc = 12 12, RLOAD = 1 kſN, IBIAS = 10.2 mA, and B = 100, what is the value of Vc1? Round to nearest volts. Note that if you are using LTspice to simulate this problem, the default LTspice model for the NPN already suffice the given transistor properties. V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer ASAP. I'll give upvote, thank you. Attach C to B, forming a BJT. In forward active mode, why does a large current flow in the base-collector junction, even though it’s reverse-biased? Answer in 1 sentence.
For the circut below measurement indicates that Vb = -1.5V. a) Assuming Vbe=0.7, calculate Ve,α,β and Vc. b) If a transistor with β = ∞ is used, what values of Vb, Ve and Vc result ?
a) Assume that the transistor in the given circuit of is replaced with one having a βDC = 200. Determine IB, IC, IE, and VCE given that VCC=10 V and VBB=3 V. RB = 34 b) Draw the IC-VCE characteristic curves of an npn transistor. c) Mention the biasing of each pn junction in each mode of operation and discuss the applications for different modes of BJT operation.
IBQ, ICQ, VE, VCEQ, VC for a transistor with VBE = 0.6 and β = 50. Draw and label the DC load-line. From b, if transferred to the center of the load-line, determine the new values of R1 and R2 and draw the final circuit.
For the 2 circuits shown above if βnpn = 100 and βpnp = 50 and VDO = 0.7 V, determine the rangesof R2 and RB to keep the transistors in the active mode.(hint: Conditions of active mode VBE = VDO and VBC < 0 for NPN transistors and VEB = VDO andVCB < 0 for PNP transistors)
In the circuit given below, VDD = 20 V and IDSS = 20 mA and Vp = -1 V for both transistors (T1 and T2). For T1 and T2 transistors; a)-Calculate IDQ1 , VGSQ1 and VDSQ1 for T1 transistor with a mathematical (analytical) approach? b)-Calculate IDQ2 , VGSQ2 and VDSQ2 for T2 transistor with a mathematical (analytical) approach?
The current source for a current switch is implementedwith a transistor and three resistors, as shown. What is the current IEE? What is theminimum permissible value of VREF if transistor QSis to remain in the forward-active region? Assumethat βF is large.
Given VTH=1.2 and k=0.5mA/V2, determine the following a) The value of ID, VGS and VDS b) Mode of operation of the MOSFET. (Verify this answer)
For the transistor , IS = 6 × 10−16 μA, βF = 100, and βR = 0.25. (a) Labelthe collector, base, and emitter terminals of thetransistor. (b) What is the transistor type? (c) Labelthe base-emitter and base-collector voltages, VBEand VBC, and the normal directions for IE , IC, andIB. (d) Find the values of IE , IC, IB, VBC, and VBEif I = 175 μA.
There is a BJT NPN transistor, base biased with voltage divider with R1 = 15K and R2 = 6K, RE = 3K, RC = 1.2k, bias voltages + 8V and -5V. Obtain the following parameters for a BETA of 80: to. Base current b. Collector current c. Collector-emitter voltage d. BJT region of operation
Q3 a) A transistor can be operated in saturation, active and cut-off region. What are the normal conditions of bias across the transistor to operate it in these different modes? b) Draw the complete circuit diagram of a transistor connected in CC mode with proper biasing along with its input output characteristics c) Draw the complete circuit diagram of a transistor connected in CE mode with proper biasing along with its input output characteristics.
An npn transistor with IS = 5×10−16 μA, βF = 100,and VA = 65 V is biased in the forward-activeregion with VB E = 0.72 V and VC E = 10 V.(a) What is the collector current IC? (b) Whatwould be the collector current IC if VA = ∞?(c) What is the ratio of the two answers in parts (a)and (b)?