and fill out the blanks:

Q: Find the distance

A:

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: Draw isometric projection of casting, two views (FV and TV) of which are shown in figure in First…

A: Refer the following image for the the required rough sketch of isometric view of the given…

Q: WRITE THE ANSWER, SOLVE IT CLEARLY

A: Acceleration, a=Wma=-gro2r2=dvdta=dvdr×drdta=dvdr×vvdv=adrvdv=-gro2r2drIntegrate…

Q: Prove please!

A:

Q: Q/draw the projections

A: According to the details provided in the question, we need to calculate THREE PROJECTION VIEW.

Q: Question#2 Find the cutting force on the metal sheet. 200 N 175 mm 40° 30 mm 100 mm 60 mm .75 mm

A: For the given arrangement  To determine  cutting force (F) on the metal sheet

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: Sheet No.2 1- Write a program to find the average of 50 numbers and print the result.

A: Question (1) is Solved here. For Other Question, please Post again.

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: Determine the names of the figures below

A: Find Name the given figures provided in the drawing sheet.

Q: 9. the force acting along a line equal to magnitude of force times... *

A:

Q: What is the force produced by an actuator to open a valve if its diaphragm has a 4-inch diameter and…

A: Given data:

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Determine of the best size

A: Given; A metric thread of pitch;P=2 mmThread angle; 2θ=600or, θ=200

Q: o the turbin

A:

Q: Find the reorder point to achieve

A: Given;   Company uses 2555 units of an item annually.Delivery lead time , T=8 days

Q: Fill the blanks correctly and define

A: Given: For apinion of 15 teeth,where, Pinion is usually a two meshed gears. It is used in several…

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: How many cubic feet of metal are required to make 1000 funnels such as the one shown in the sketch…

A: The periphery enclosing a certain amount of volume in space is termed as the curve surface area.…

Q: Please show all work and answers. If not ALL then please answer ones in RED. Thank you.

A:

Q: Draw the front, Top , and side planes for a complete cut *Note the shape is symmetrical

A: a. Front b. Side c. Top

Q: 8.[Short Answer] As shown in this figure, what's the function of inclined plate colored yellow ?

A: Ans : The structure is showing like truss system where five members or links are attached to each…

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: 4. WHAT IS THE VOLUME OF THE PART?

A: Given:- Unit:- MMGS Material:- Copper To find:- 1) Volume 2) Mass 3) Center of mass

Q: Determine the total increase in length.

A: Given: E1=175 GPa E2=210 GPa P=55 kN To determine: Total increase in length

Q: Shear force is unbalanced to the left or right of the section.

A: The shear force  of a beam may also be defined as the unbalanced vertical force to the left or right…

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: (a) in

A: (a) when ball displace with angle θ then natuaral frequency for case 1st moment of inertia of disl…

Q: determine the minimum preferred size diameter.

A: Given: FOS=3  T2=0.15T2 To determine: The minimum diameter using distortion energy theory

Q: The shear angle

A: Given data: An ortogonal turning operation is carried out under the following condition: Rake…

Q: Findss 30 kN-m

A:

Q: ??

A: Converting water or liquid to extremely high temperature using any source of heat until it gets…

Q: 50 MPa

A: The Mohr’s circle is used to determine the principal stresses, normal and shear stress at various…

Q: y 1 in. 3 in. -3 in.-

A: Area of the triangle, A1=1/2(3)6=9in2 Area of the square, A2=3(3)=9 in2 Area of the quarter circle,…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm…

A:

Q: Given the drawing below, answer questions

A: 11) For G dimension Since, G = 3-0.3+0 So, basic size = 3 Tolerance = 0-(-0.3) = 0.3 Maximum size =…

Q: haft trar Is, then t

A: given:power P=1000kwω=100rad/s

Q: Determine blank diameter ?

A: Given data; Height with corner radius, r= 0.7 mmshell diameter,d =900 mmHeight, h=200 mmIt is…

Q: How did 6650 mm2 come from please show the work.

A:

Q: 3T tanux

A:

Q: A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its inside…

A: Given Data Height of the cup, h=75 mm Inside diameter, Di=400 mm Sheet metal thickness, t=20 mm…

Q: Can I have the formula for the percent difference?

A:

Q: Find results of forse

A:

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

A:

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.