hellooo, please helpp Part I. Indicate/Mark (by using your pen or any app) the part of the instrument where youobtained each reading.4525,001 in.51015205 10 1406 71.8 92 3III4050607080903530O 1 2 35 6 78 9 1O0,02 mm4Answers must be handwritten.2. Vernier Caliper English 3. Vernier Caliper Metric1. Micrometera. SleeveReading=b. ThimbleReading=ScaleScalea. FixedReading=.b. VernierReading=.Scale a. FixedReading=.Scale b. VernierReading=.ScaleScale

Answered: Image /qna-images/answer/d0f8a3e9-e6e0-4062-9561-23d93121dc70.jpg

Part I. Indicate/Mark (by using your pen or any app) the part of the instrument where you obtained each reading. 45 15 20 25 .001 in. 10 0 5 1O luull 40 5 67 40 50 60 70 80 90 35 6 10 0,02 mm 2 3 4 Answers must be handwritten. 1. Micrometer a. Sleeve Reading= b. Thimble 2. Vernier Caliper English 3. Vernier Caliper Metric Scale Scale a. Fixed Reading= b. Vernier a. Fixed Reading= Scale b. Vernier Reading= Scale Scale Reading= Scale Reading=

Part I. Indicate/Mark (by using your pen or any app) the part of the instrument where you obtained each reading. 45 15 20 25 .001 in. 10 0 5 1O luull 40 5 67 40 50 60 70 80 90 35 6 10 0,02 mm 2 3 4 Answers must be handwritten. 1. Micrometer a. Sleeve Reading= b. Thimble 2. Vernier Caliper English 3. Vernier Caliper Metric Scale Scale a. Fixed Reading= b. Vernier a. Fixed Reading= Scale b. Vernier Reading= Scale Scale Reading= Scale Reading=

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Similar questions

A 150.00-mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m
The addition of a vernier scale on the barrel of a 0.001-inch micrometer increases the degree of precision of the instrument to 0.0002 inch. True or False
If a 5.5 kg weights are added to bourdon gauge the reading on the of the gauge should be (assuming no error ) Select one: a. none b. 0.171224 N/mm2 c. 171.22KN/m2 d. 0.01746 KG/mm2
(i) Give the correct number of significant figures for: 4500 0.0032 0.04050 (ii) Write in scientific notation and engineering notation: 0.000467 32000000
1)Meaning of the term "Grade" in a grinding wheel is a. How much spacing between the abrasive grains in the grinding wheel b. The ability of the abrasive grains to hold together to form the grinding wheel c. The strength of the bond inside the grinding wheel d. The abrasive grain size used in grinding wheel production 2)In a Vernier Caliper if the vernier scale with ______________divisions (lines), will be 0.05 mm least count. a. 50 b. 30 c. 20 d. 40
The least count of a micrometer is a. 0.01 mm b. 0.2 mm c. 0.05mm d. 0.1mm
An irregular shaped metal sheet is to be constructed with a measurement of 5.5m x 6.2m x 7.7m x 4m x 3.65m. Do the necessary calculation in order to design in inches the metal sheet on a drawing sheet if the design scale is 1:255.
When several measured values agree with one another, the values are said to be accurate neither accurate nor precise both accurate and precise precise
Incorrect answer I've tried below (should be in inches) .0152 7.64*10^-3 .00556 29007 .0101 .0122
In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70 (+0.04 )/(+0.00 ) mm and Shaft = 70 (-0.04)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Read the following Vernier caliper measurements. (The scales have been enlarged for easier reading.) The Vernier caliper is calibrated in metric units. Please read the actual reading with solutions. Answer the letter f and d plss. Thank u