Answe rite the sentence on for 10 only 1- Mn Ni Cr, W, Mo, V are the most important elements that forming Austenite. 2- Diamond Pyramid is used for the Scale C in Rockwell hardness test. 3- The stress of forming process must exceed UTS yield point. 4- The brittle transition temperature of steel is within -4 °C to 4°C. 5- Quenching process for steel is used to increase the ductility. 6- The annual quantity production of high production process is more than ten thousand. 7- Knoop test method is used to test the thick and hard material with little load.

Answe rite the sentence on for 10 only 1- Mn Ni Cr, W, Mo, V are the most important elements that forming Austenite. 2- Diamond Pyramid is used for the Scale C in Rockwell hardness test. 3- The stress of forming process must exceed UTS yield point. 4- The brittle transition temperature of steel is within -4 °C to 4°C. 5- Quenching process for steel is used to increase the ductility. 6- The annual quantity production of high production process is more than ten thousand. 7- Knoop test method is used to test the thick and hard material with little load.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As the tempering temperature of a heat treated steel increases the associated values of Brinnell hardness also increase, while the values of tensile strength and yield strength decrease. True or false
The S-N curve which represents the fatigue strength, which is measured as a stress amplitude, as a function of number of stress cycles, can be approximated by a straight line in therange of 103cycles to 106cycles when plotted as log(S) versus log(N). Beyond 106cycles,the fatigue strength remains constant. The fatigue strength of a certain alloy at 103cyclesis given as 80 % of the ultimate tensile strength and its endurance limit is 50 % of theultimate tensile strength.(a) The alloy part fails in 15 000 cycles. Calculate the percent change (increase or decrease)of the maximum applied cyclic stress amplitude if the life of the part needs to beextended by 3.5 times. Is this considered under a high or low cycle fatigue failure?State any assumptions made. (12 marks)(b) If the applied cyclic stress amplitude remains unchanged when the life is extended by3.5 times, calculate the percent change (increase or decrease) of the ultimate tensilestrength of a new alloy required. (8 marks)(c) If the…
A 2.0-inch diameter 4140 steel bar is austenized and tempered in oil without Agitation, determine the resulting hardness at 0.6 inches below the surface, present all the Procedure to arrive at the answer (include sketch of the piece and graph used with steps Using word forms)
Q1: 1.5 in diameter steel part is quenched in oil with no agitation. (H=0.20). If we use a 4340; 4140; 8640; 5140; 1040 steel, what would be the hardness number at the center of the part? Q2: Determine the best quenching medium to produce a minimum hardness of HRC 40 at the center of a 3.75 cm diameter 4320 steel bar.
Drive the relation of stress transformation.
During the test of hardness due to Brinell, the diameter of the testing sphere was0.01m, the exerted load was 3.0 tons and the diameter of the indented area wasapproximately 0.003 m. Find the value of the hardness for this material. Also find theTensile strength if the proportionality constant was approximately 3.45.
The cold work is gevn for 15% then determine the upcoming values of its stength if the material is An annealed steel the properties of the material is Sy = 32.0 kpsi, Su = 49.5 kpsi,σf = 91.1 kpsi, σ0 = 90 kpsi, m = 0.25, and εf = 1.05 in/in. assume steel type :An annealed AISI 1018 steel please give detiled answer if expecting upvote
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
A steel cylinder (Est = 200 GPa and G = 79 GPa) undergoes an azial compression in which its diameter increases from 10 mm to 10.045 mm. If its final length is 123.00 mm, what was its original length?
hi im reviewing my class notes and im confused as to how it obtained the answer of 87.47 Mpa. P.S. this topic is stress transformation
Fatigue data of steel is showed in the following stress-cycle curve.Write down the values of steel endurance limit and steel fatigue strength at 10^5 cycles in the spaces provided below.Steel Endurance Limit: _____ ksiteel Fatigue Strength at 10^5 cycles: _____ ksi
A 30 ?? square plate is subjected to uniform pressure as shown in Figure.1. The 2D loading stressesare described. If the modulus of elasticity is 200 ??? and the lateral constant (Poisson's ratio ? = 0.3). Estimatethe change in length in the vertical, horizontal and diagonal sides as well as determine the volumetric strain.Illustrate the effect of two-dimensionalstrain by constructing appropriate sketches (before and after deformation).Repeat the analysis for lower value of pressure and higher value in the range of [20 -100 MPa] and comment onthe overall results.