supplied by aare€ Twoindustrial IloadsSource thrugha trans mission line with a lineImpedonce 0.1 + 1or. If the two conditionsgiven forloud arethea) 44 Kw at 0.82 pf laggingb) l64 Kw at 0.92 pf laggingDetermine the power factor at the load,If the Voltage at thelouds are 240,angle 0. rms

We first calculate the active power and reactive power of each load. Sum power and reactive power to…

are supplied by a E Two industrial Iloads Surce thragh a trans mission line with a line Impedonce 0.1 + 1or, If the two conditions Jozr. given for the loud are a) 44 Kw at 0.82 pf lagging b) l64 Kw at 0.92 pf lagging Determine the Power factor at the loud, If the Voltage at the loads are 240, angle 0. rms

are supplied by a E Two industrial Iloads Surce thragh a trans mission line with a line Impedonce 0.1 + 1or, If the two conditions Jozr. given for the loud are a) 44 Kw at 0.82 pf lagging b) l64 Kw at 0.92 pf lagging Determine the Power factor at the loud, If the Voltage at the loads are 240, angle 0. rms

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
An AC generator having an internal resistance of 2 k*(omega) is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, E = 282 sen (100*pi*t) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
Suppose the circuit shown represents a residential distribution circuit in which the impedances of the service conductors are negligible and Vg1=Vg2=120 0° V (rms). The three loads in the circuit are L1 (a new refrigerator, a coffee maker, and a microwave oven); L2 (2 incandescent lamps, a humidifier, and a ceiling fan); and L3 (a clothes washer and a clothes dryer). Assume that all of these appliances are in operation at the same time. The service conductors are protected with 20 A circuit breakers. Will the service to this residence beinterrupted? Why or why not?
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by (a) 1202cos(t+60) (b) 120cos(t+60) (c) 1202sin(t+60)
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
A load with a voltage amplitude of 50 Hz 300 V rms at its terminals consumes 28.98 kW at a back power factor of 0.69. If a 225.87 microfarad capacitor is connected parallel to the terminals of this load, how much will the amplitude of the current drawn from the line decrease?