Argon enters a steady-state throttle valve at a pressure of 300kPaand a specific volume of 0.55m/kg What is the exit temperature if the exit pressure is 100kPa? Report your answer using units of Kelvin and to three significant digits. Do not round numbers used in your computation. Only round the final numeric answer.

Argon enters a steady-state throttle valve at a pressure of 300kPaand a specific volume of 0.55m/kg What is the exit temperature if the exit pressure is 100kPa? Report your answer using units of Kelvin and to three significant digits. Do not round numbers used in your computation. Only round the final numeric answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Early mountaineers boiled water to estimate their altitude.If they reach the top and fi nd that water boils at 84 ° C,approximately how high is the mountain?
State what is Bernoulli's Priciple for Pressure and Velocity? In 8 sentences only.
5. Consider a Pitot probe in high-speed flow.(c) You are flying through air at static p∞ = 0.8 atm [abs]. Your velocimeter broke,but you are still receiving the following direct stagnation pressure readings (atm[abs]) from the Pitot probe mounted on your aircraft’s noise: i) 3.152 ii) 1.357 iii) 38.428 iv) 0.8 Find the freestream Mach number corresponding to each of the pressure readings. (d) If we are to believe reading (iv), can we step out of the aircraft safely? Why?
A cylindrical tank shown below has a radius ? and a circular orifice at the bottom of radius ?. At time ? = 0 the liquid level in the tank is ho. (a) Use the Bernoulli equation to determine the relations between the orifice velocity ?o and the free surface velocity ?s (assume the surface velocity is not zero). (b) Use conservation of mass to determine the orifice velocity in terms of the free surface velocity. (c) Use the results in (a) and (b) to derive a differential equation for h(?). Note that ?s = − dh/dt. d) Separate variables and solve the equation for h(?) with the initial condition h(0) = ho (e) Determine how long it will take to empty the tank.
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.16 cm water gage. The duct diameter is 1.22 m, the barometric pressure 99.4 kPa and the gage flt*d temperature and air temperature are 30 C. What is the total pressure against which the fan will operate in cm of water?
For supersonic and hypersonic wind tunnels, a diffuser efficiency, ηD,can be defined as the ratio of the total pressures at the diffuser exit andnozzle reservoir, divided by the total pressure ratio across a normal shockat the test-section Mach number. This is a measure of the efficiency ofthe diffuser relative to normal shock pressure recovery. Consider asupersonic wind tunnel designed for a test-section Mach number of 3.0which exhausts directly to the atmosphere. The diffuser efficiency is 1.2.Calculate the minimum reservoir pressure necessary for running thetunnel.
TOPIC: FLUIDS AT REST AND MOTION Water flows through a horizontal pipe with a diameter of 4 cm at a speed of 6 m/s with apressure of 400kPa at point A. At point B, the diameter is 2 cm. (a) What is the speed of water at point B. (b) Calculate the pressure at point B. Please help me solve this problem with complete solution. Please include an illustration. Thank you tutor!
H2O gas enters a convergent-divergent nozzle, with pressure 5 MPa, and temperature 2000∘ C. Flow enters with negligibly small velocity. The exit temperature T is 909 K. The flow velocity at the throat section is (in m/sec), Group of answer choices 700 800 900 1000 1100 Solve it correctly please. I will rate accordingly with multiple votes. Do it correctly.
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
A wind tunnel has an incompressible flow of air, flowing horizontally from an inlet section, 7 times the test section. A u-tube is connected, containing mercury inside. The mercury has 1.33x10^5 N/m^3 specific weight. The condition of the air at the inlet section is at 1 atm and 280K respectively. What is the change of height inside the mercury, when the velocity at the throat is 70m/s?Complete solutionround off to 4 decimal places
Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid