Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the flow of water. The pressure  at inlet is 20 N/cm2 and the vacuum pressure at the throat is 27 cm of mercury. Find the rate of flow. The value of cd may be taken as 0.9

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 10 cm respectively. The…

A:

Q: (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow.

A:

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The…

A:

Q: The rate of flow of water in a pump installation is 60.6 kg/s. The intake static gage is 1.22 m…

A:

Q: nlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The liquid…

A:

Q: A horizontal Venturi meter is shown in Figure 8 to measure the flow rate of water in the main pipe.…

A:

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A:

Q: A fan delivers 5.1 m^3/sec at a static pressure of 6.167 cm of water when operating at a speed of…

A:

Q: A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill…

A: Given that, diameter of pipe= 14 cm                           =0.14m height of the hill from ground=…

Q: A horizontal Orifice meter is used to measure the flow rate of water through the piping system of 20…

A:

Q: A certain centrifugal pump was tested and its performance curves can be approximated as follows: H =…

A:

Q: 1) A steady, incompressible fluid flow through two identical pumps in series, the volume flow rate…

A: 1) A steady, incompressible fluid flow through two identical pumps in series, the volume flow rate…

Q: The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger…

A: Larger end: D1= 0.50 cmZ1= 7 mV1= 1.2 m/sP1= 5200 kN/m2 Smaller end: D2= 0.20 cmZ2= 3 m   To find:…

Q: Inlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The…

A:

Q: Q1/ The pressure drop in pascals (Pa) for a fluid flowing in a pipe with a sudden decrease in…

A: Given dataFormula for pressure drop is given.We have to develop a MATLAB script to read values of…

Q: The Water is flowing through a pipe having diameter 350 mm and 210 mm at the bottom and upper end…

A:

Q: An orifice of 2.58 cm diameter is placed in a pipe of 5.1 cm diameter. The pipe delivers oil of…

A:

Q: B4. An orifice meter with orifice area 848 mm2 is inserted in a pipe of area 1696 mm2 .The pressure…

A: Given fluid in pipe is oil with specific gravity of 0.75 and not water .Hence there is correction in…

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is…

A: Given DataN=1400 rpmr2=0.21mβ2=158°Cr2=4m/s

Q: 3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter,…

A: Given: The volume flow rate of brine, Q = 126 liters/s = 0.126 m^3/s The specific gravity of brine,…

Q: A fan delivers 4.804 m^3/sec at a static pressure of 5.245 cm of water when operating at a speed of…

A: Please find the answer below

Q: A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm…

A: Velocity of stream is given by the following formula, V=Cv✓2gh Where Cv=coefficient of velocity

Q: 26. Inlet and throat diameters of a horizontal venturimeter are 270 mm and 130 mm respectively. The…

A:

Q: 1. Oil (sg = 0.82) enters a pump through a 20 cm diameter pipe at 40 kPa. It leaves the pump at 125…

A: Given,  Specific gravity of oil ,  S = 0.82. Inlet pipe diameter , d1 = 0.2 m outlet pipe dimeter…

Q: An oil refinery uses a Venturi tube to measure the flow rate of gasoline. The density of the…

A: Given data Density of gasoline = 710 kg/m3Radius at point 1 = 2.36 cm = 2.36 x 10-2 mRadius at point…

Q: soft drink (mostly water) flows in a pipe at Asia Brewery with a mass flow  rate that would fill 220…

A:

Q: At point A in the pipeline conveying water, the diameter is 1 m, the pressure 100 kPa and velocity 1…

A:

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A:

Q: A centrifugal pump having a suction diameter of 254 mm and a discharge pipe diameter of 127 mm has…

A:

Q: A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of…

A: Write the given values along with the suitable variables.

Q: 2. The diameter of a pipe at the larger end is 0.5 cm and at the smaller end is 0.2 cm, the larger…

A: Data given - PA = 5200 kN/m2  VA = 1.2 m/s  DA = 0.5 cm  DB = 0.2 cm  ZA = 7 m  ZB = 3 m

Q: total energy

A:

Q: (Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: . A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and…

A: Here given data says that  Hight ,= 30 m  Diameter at bottom= 6 m  Diameter at top = 4.5 m  Wight of…

Q: Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet.…

A:

Q: 2. The diameter of the discharge pipe of a pump is 15 cm and that of the intake pipe is 20 cm. The…

A:

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The…

A:

Q: let. What is

A: GIVEN:d1=4ftd2=2ftv1=1ft/s

Q: A two-lobe rotary positive-displacement pump moves 0.60 cm3 of motor oil in each lobe volume. For…

A: Given: The volume of each lobe is Vlobe=0.6 cm3. The number of lobe is N=2. The rate of rotation of…

Q: A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at…

A: we can solve this question by using :- 1)continuity equation  2) Bernoulli  equation

Q: It was determined that for a length of 1.6 km of 90 cm diameter pipe made of wood staves the head…

A:

Q: A fan delivers 5.159 m^3/sec at a static pressure of 6.703 cm of water when operating at a speed of…

A: Please find the answer below

Q: Q.No.3: An orifice of 2.58 cm diameter is placed in a pipe of 5.1 cm diameter. The pipe delivers oil…

A: The orifice is the small opening given to any of the plates through which a fluid can flow…

Q: The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston…

A: To find: The speed of the compressor. Given: The bore diameter of an air compressor is d=276 mm1…

Q: pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A: It is required to determine total energy head

Q: B4. An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure…

A: According to the given information, we have an area of orifice meter  931 mm2, area of pip is…

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A: GivenQ=35L/s

Q: what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows…

A: Velocity varies linearly with distance.V=ax+bAt x=0  V=2 m/s2=a*0+b    ......(1)At x=0.7    V=6…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.