Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.28 ✕ 10−6 m3 is formed under a pressure of 4.60 GPa. Find the change in its volume (in m3) when it is released from the press and brought to atmospheric pressure. Take the diamond's bulk modulus to be B = 194 GPa. (Assume the system is at sea level.

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the…

A: Given l=length of wire=30ft W=500lb maximum stress=20ksi elongation =0.2in E=29*10^6 psi

Q: steel cable with a cross-sectional area of 3.00 cm^2 has an elastic limit of 2.40x10^8 Pa. Find the…

A:

Q: A column 600 mm in diameter is reinforced with 8-25mme bars and 12 mm spirals spaced at 100 mm on…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A makeshift compact torsional spring is made of steel (Gst = 11,000,000 psi) and is composed of a…

A: Given that a  makeshift compact torsional spring is made of steel (Gst =11,000,000 psi) and is…

Q: What is the maximum load that could be suspended from a copper wire of length 1.00 m and radius 1.08…

A:

Q: A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a…

A:

Q: Two wires are made of the same material, their Young’s Modulus constant is 10 x10^10 Pa. Wire X is 4…

A: Given: Two wires are X & Y. Young's modulus constant, γ=10×1010 Pa Considered wire Y length be…

Q: Give answers in scientific notation. A sphere of copper is subjected to 120 MPa of pressure. The…

A:

Q: f a compressional stress of 200.0 N is applied to a copper rod having a diameter of .500 cm and a…

A:

Q: Calculate the shear modulus (G) for a cylindrical steel specimen. Assuming the elastic modulus is…

A:

Q: Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial…

A: Initial volume (V) = 1.28×10-6 m3 Pressure or Stress (P) = 5.05 GPa or 5.05×109 Pa Bulk Modulus (B)…

Q: A hollow steel propeller shaft, 20 ft. Ilong with 15 in outer diameter and 12 in. inner diameter,…

A:

Q: A 2 m long steel rod has a cross-sectional area of 0.3 cm?. The rod is a part of a vertical support…

A: The stress of the rod is given by F/A Strain is given by dL/L                    where F= Force…

Q: 20. The experimentally determined Young's modulus for brass is 9.0 × 10^10 Pa. A brass bar…

A:

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

A: Given data: Observe from the diagram, Total displacement of layers D = 2 mm Height of stripe L = 5…

Q: A solid cylindrical rod BC of length L = 600 mm and radius r = 12 mm is attached to the rigid lever…

A: Given Diflection of a is 10mm AB is 300 mm Angle = 10/300 = 0.033 rad. G = 70 GPa T = FdL = 700 N*…

Q: Find the modulus of elasticity of a cast iron rod of diameter 20 mm and length 250 mm subjected to a…

A: Diameter of rod = 20 mm So, radius, r = 10 mm = 10-2 m Length of rod, L = 250 mm = 0.25 m Tensile…

Q: The maximum upward acceleration of a lift of total mass 2500 kg is 0.5 ms, The lift is supported by…

A: Answer             2.575 X 10-4m2

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If…

A:

Q: 700 KN 2.5m A 2.5-m length of a steel pipe of 300-mm outer diameter and 15-mm wall thickness is used…

A: length of pipe , L = 2.5m=2500mm outer diameter d0 = 300mm wall thickness t = 15mm Axial compressive…

Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm and length 250 mm…

A: Cross section Area, A = 20x20 mm2                                 A= 400 X 10-6 m2 Length, L = 250…

Q: Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial…

A: It is given that

Q: A copper wire of length 2.2m and a steel wire of length 1.6m both of diameter 3.0mm, are connected…

A:

Q: A specimen of oil having an initial volume of 600 cm3 is subjected to a pressure increase of 3.6 *…

A: Given, Initial volume, V0=600 cm3, pressure increase, ∆P=3.6×106 Pa, and volume decrease, ∆V=0.45…

Q: 2.47 The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the…

A:

Q: The pressure at a depth of 1.0 km in the Pacific Ocean exceeds by 10 mega Pascal. If a metallic…

A: Pressure difference (∆P) = 106 Pascals Volume of metallic alloy (V) = 385 cm3= 3.85×10-4 m3Bulk's…

Q: Straight wooden stick has mass M=0.40kg, Length L=1.2m, uniform cross-section A=18cm2, and constant…

A: GivenM=0.4 kgL=1.2 mA=18 cm2=18×10-4 m2Andm=0.2 kgDensity of water, ρw=1010 kg/m3

Q: Q. 10. 9 Some claim that mountain climbers suffer from headaches due not only to a lack of oxygen…

A:

Q: A cube with edges exactly 2 cm long is made of material with a bulk modulus of 3.5 x 10 9 N/m 2.…

A: The Bulk Modulus of a system is given as

Q: The velocity v (m/s) of air flowing past a flat surface is measured at several distances y (m)…

A: Newton’s viscosity law,

Q: H horizontal force of P = 1,400 lb is applied to the rectangular bar shown in Figure above. d = 1.80…

A:

Q: Consider a structure including the horizontal beam AB hinged to the wall at point A and supported by…

A: According to our policies, I can answer only first three subparts of this problem. The detailed…

Q: 3. A steel beam is placed vertically in the basement of a building to keep the floor above from…

A:

Q: Suppose that an object was formed using 7.25 x 10° Pa. When it was released from the press and…

A: Given  :     Pressure, P1 = 7.25*108 Pa     Pressure, P2 = 1.01*105 Pa       Change in Pressure, ∆P…

Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm, and length 248 mm…

A: Tensile load(T)= 50 KN Elongation (e)= 0.25 mm = 2.5× 10-⁴ m Length of the rod(L)= 248 mm= 0.248 m…

Q: A 480 mm long thighbone (femur), which is the largest and longest bone in the human body, has a…

A: Given that  young modulus = 15x 108 N/m2 length of femur = 480 mm =0.480 m cross sectional area =…

Q: Two wires are made of the same material, their Young’s Modulus constant is 10 x10^10 Pa. Wire X is 5…

A:

Q: You hang a heavy ball with a mass of 14 kg from a gold wire 2.5 m long that is 2 mm in diameter. You…

A:

Q: The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical…

A: Given information:The side length of the aluminium cube (l) = 10 cm = 0.1 mThe mass of the…

Q: Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial…

A: Explanation From the defintion of Bulk modulus we get, B=-∆P∆VV  .......................(1) where is…

Q: A steel rectangular block, a = 2.4cm wide and b =1.2 cm deep, is subjected to an axial tensile load…

A: Modulus of elasticity for a volume object is known as Bulk modulus of elasticity.

Q: Some claim that mountain climbers suffer from headaches due not only to a lack of oxygen in the…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).