3. The figure shows contraction of the venturi meter pipe, assume there is no energy loss,and subcritical flow.With the equation:29(y1-y2) )1/2 , b1 = 3 m, b2 = 2 m, y1 = 1,9 m.Q = (-b2²y22¯b1²y1²1• Find Q if y2 = 1.5 m• - Find y2, if the flow in the transition area becomes criticalb,Top viewSide view

Given: To find: Q if y2 = 1.5 m

Answered: 3. The figure shows contraction of the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water flows to the nozzle through a 180-degree elbow. The pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure. Please use conservation of momentum (momentum equation) and draw the control volume since that is our lesson.
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
2) The horizontal pipe of diameter 240 mm is suddenly enlargement to a diameter of 480 mm. if the pipe carries water at 325 liters/sec, calculate the (i) Head loss to sudden enlargement,(ii) Pressure loss across the enlargement (p1-p2).
Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius horizontal pipe. If the bore of the pipe is reduced to 2.7-in radius and the pressure in the smaller pipe is 93 psig, what is the pressure in the larger section of the pipe? Include schematic diagram.
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
choose the correct answer Q1A- Losses of pressure in fluid due to resistance by viscose shear stresses are: * a) Minor losses b) Fitting losses c) Friction losses d) Total head losses e) None of all above B- when pipe with the different diameter are connected by series, then total losses will be the sum of each pipe losses * a) True b) False
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
12. Points A and B are 3000 ft apart along a 10-in. new steel pipe. B is 220 ft higher than A. With a flow of 3.2 efs of water from A to B, what pressure must be maintained at A if the pressure at B is to be 50 Ib per sq in.? Answer should be: 164 lb per sq. inch Show your handwritten solution.
Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 895.55 L/min from the reservoir and through the pipe shown in the Fig. below. Compute the pressure at point B, considering the energy loss due to friction, but neglecting other losses. Also, use pipe roughness of 1.50 X 10-6 m. Hint: Use the appropriate formula to determine the friction factor, f to 4 decimal places (flow type dependant); g = 9.81 and round off to 3 decimal places for all other step calculations leading to the final answer including the final answer.
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flow through the pipe, what must be the pressure at A?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS