As time progresses, all quantities will decay exponentially: Q(t) = Qoe-t/RC. Qois the value calculated previously, but what R must be used? (Calculate its value in Ohms.) Switch R1=40 0 R3= 30 2 60 03 E= 12 V R2 C = 2 µF = V1, V2, V3, and 1, I2, I3apply to the respective resisters. Vc and Q refer to the capacitor's voltage and charge. Uc refers to the capacitor's stored energy (electric potential energy).

As time progresses, all quantities will decay exponentially: Q(t) = Qoe-t/RC. Qois the value calculated previously, but what R must be used? (Calculate its value in Ohms.) Switch R1=40 0 R3= 30 2 60 03 E= 12 V R2 C = 2 µF = V1, V2, V3, and 1, I2, I3apply to the respective resisters. Vc and Q refer to the capacitor's voltage and charge. Uc refers to the capacitor's stored energy (electric potential energy).

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter14: Inductance

Section: Chapter Questions

Problem 14.7CYU: Check Your Understanding Verify that RC and L/R have the dimensions of time.

See similar textbooks

Similar questions

Why can a null measurement be more accurate than one using standard voltmeters and ammeters? What factors limit the accuracy of null measurements?
what is the factor for a cabe at 5degree celcius when calculating resistance od a cable? option answer 0.94 0.98 0.96 1.02 ??
A high tension (HT) supply of, say, 6 kV must have a very large internal resistance. Why?
Regarding the units involved in the relationship τ = RC, verify that the units of resistance times capacitance are time, that is, Ω ⋅F=s.
What voltage is required to be applied during open-heart surgery to utilize a defibrillator for reviving a patient from cardiac arrest, given that the path's resistance is 0.500 kΩ and a current of 12.0-mA is necessary?
in the curcuit shown in the figure , the S switch is closed at t = 0 and the capacitors, which are completely empty, begin to fill. Here E = 20 V , C = 4uF and R = 30 ohm. a) what is the time constant of the circuit , T in units of microseconds? b)when t=T , what is the total charge , in units of microcloumb accumulated in the capacitors ?
Using the exact exponential treatment, find how much time (in s) is required to charge an initially uncharged 120 pF capacitor through a 67.0 MΩ resistor to 91.0% of its final voltage. __________s
Calculate the ratio of the resistance of 20.0 m of copper wire 1.8 mm in diameter to 10.0 m of aluminum wire 2.0 mm in diameter, (i.e. RCu/RAl =?)
In the circuit shown in the figure, the S switch closed at t=0 and the capacitors, which are completely empty, begin to fill. Here ε=10 V, C=5 μF and R=55 Ω. What is the time constant of the circuit, τ, in units of microseconds? When t= τ, what is the total charge, in units of microcoulomb, accumulated in the capacitors?
An engineer built the circuit depicted in the figure. Assuming = 8.40 V and R = 4.90 Ω. What is the magnitud (mA) of the current in the 2.00 Ω resistor and what is the potential difference (in V) between points a and b (Vb − Va)?
show that RC has a unit of seconds if R is in ohms and C is in F
What is true in general about the voltage (potential) supplied by the battery compared with the drop in potential across the resistor? What can you conclude about the drop in potential because of the wires, switch and ammeter?