ASME Y14.5-2009. PART TO BE FREE OF BURRS AND SHARP EDGES. D.001 VACUUM, BAKE (10-4 TO 105 TORR). TEMP RISE 300 C/10 MIN TO 900 C. HOLD FOR 15 MIN AT 900 C. COOL TO 500 C IN 10 MIN, 500 C TO 100° C IN 30 MIN, REMOVE AND AIR COOL TO ROOM TEMP (20 C). THREAD RELIEF .10 LONG MAX. 2.125 A /.001 A 2.059 IDENTIFY IAW MIL-STD-130 BY BAG AND TAG INCLUDE LATEST REV LEVEL. 1.914 ELECTROLESS NICKEL PLATE PER MIL-C-26074, CL 2 (.0001/.0002 THK). .867- DIMENSIONS TO APPLY AFTER FINISH. GOLD PLATE INDICATED SURFACE PER MIL-G-45204, TYPE_I, GRADE A, CLASS OPTIONAL, THICKNESS TO BE LESS THAN .0005 PER SURFACE. 69 .040- 2X 45 X .010 - 45° X .015 Ø1.274 ø.674 &.010 B Ø.660±.002 O ø.028@ AB $ø.028© AB ø.8740±.0005 |+ ø.014@| A B 0.001 A .875–40 UNS-2A R.005 MAX- ø.107±.001 THRU Uø.218 TO FULL DIAMETER FAR SIDE ONLY + ø.028@ AB

ASME Y14.5-2009. PART TO BE FREE OF BURRS AND SHARP EDGES. D.001 VACUUM, BAKE (10-4 TO 105 TORR). TEMP RISE 300 C/10 MIN TO 900 C. HOLD FOR 15 MIN AT 900 C. COOL TO 500 C IN 10 MIN, 500 C TO 100° C IN 30 MIN, REMOVE AND AIR COOL TO ROOM TEMP (20 C). THREAD RELIEF .10 LONG MAX. 2.125 A /.001 A 2.059 IDENTIFY IAW MIL-STD-130 BY BAG AND TAG INCLUDE LATEST REV LEVEL. 1.914 ELECTROLESS NICKEL PLATE PER MIL-C-26074, CL 2 (.0001/.0002 THK). .867- DIMENSIONS TO APPLY AFTER FINISH. GOLD PLATE INDICATED SURFACE PER MIL-G-45204, TYPE_I, GRADE A, CLASS OPTIONAL, THICKNESS TO BE LESS THAN .0005 PER SURFACE. 69 .040- 2X 45 X .010 - 45° X .015 Ø1.274 ø.674 &.010 B Ø.660±.002 O ø.028@ AB $ø.028© AB ø.8740±.0005 |+ ø.014@| A B 0.001 A .875–40 UNS-2A R.005 MAX- ø.107±.001 THRU Uø.218 TO FULL DIAMETER FAR SIDE ONLY + ø.028@ AB

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

explains how the two methods of parameter estimation, namely the method of parameter estimation and the method of moments and percentile matching, are used to fit distributions to data for actuarial calculations.
Answer the following questions based on scaling arguments, i.e., by applying “the variable X must be proportional to the Zth power of variable Y because of some relevant physical principle”-type reasoning. A. In a surface passivation process for Si wafers, the required processing time to create a 0.1 micron thick SiO2 layer on a pure Si wafer was 2 hours. Estimate the process time required to create an SiO2 layer of thickness 0.15 microns on a pure Si wafer under identical processing conditions. B. A puddle of volatile liquid of initial thickness of 1 cm was found to evaporate to form a thinner 0.5 cm layer in 1 day. How much longer would it take for the liquid layer to evaporate completely?
P=17000000
The processing of raw coal involves “washing,” in which coal ash (nonorganic, incombustible material) is removed. The article “Quantifying Sampling Precision for Coal Ash Using Gy’s Discrete Model of the Fundamental Error” (Journal of Coal Quality, 1989:33–39) provides data relating the percentage of ash to the volume of a coal particle. The average percentage of ash for six volumes of coal particles was measured. The data are as follows: Volume (cm3) 0.01 0.06 0.58 2.24 15.55 276.02 Percent ash 3.32 4.05 5.69 7.06 8.17 9.36 Using the most appropriate model, predict the percent ash for particles with a volume of 48 cm3. Round answer to three decimal places. * the answer i got was of 6.260 was wrong
PLS ANSWER ASAP. THANK YOU! The slope of the calibration curve is based on __________. a. calibration limit b. calibration sensitivity c. calibration detection d. calibration function
How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is that your diving by f/a and multiplying by 83 to get H , im just no sure what you did to get 16 ?.
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
The same engineer decides to look into rates of cooling for liquids toexperiment with different cooling solutions for servers. She finds thatthe rate of cooling for one liquid can be modelled by the equation:y = 48 × 0.99t(0 ≤ t ≤ 80)where y is the temperature of the liquid in degrees Celsius and t is thetime in minutes.(i) State whether the type of reduction for this model is linear orexponential. Describe how reduction rate differs between linear andexponential functions. (ii) Calculate the temperature when t = 20. [3](iii) Write down the scale factor and use this to find the percentagedecrease in the temperature per minute. (iv) Use the method shown in Subsection 5.2 of Unit 13 to find the timeat which the temperature is 30◦(v) Determine the halving time of the temperature.
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit. t1 = 22.760 is incorrect
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit.
As8 Assuming that this is the FIRST onland discovery on island (meaning: we do not have a similar reserve discovered and developed earlier in the neigbouring areas), out of the general 4 methods of evaluating the OOIP, which method should be directly eliminated?Why?
write .687+/- .0003 as a limit dimension