Assume that an LC-3 machine instruction "0011000000000110" is stored at address Ox3702, label A corresponds to memory address Ox3709, label B corresponds to memory address Ox3708, and, label C corresponds to memory address Ox3707. Which one of the following assembly language instructions corresponds to the machine instruction? Your answer: - BRp B ST RO, B ST RO, A BRnzp C

Assume that an LC-3 machine instruction "0011000000000110" is stored at address Ox3702, label A corresponds to memory address Ox3709, label B corresponds to memory address Ox3708, and, label C corresponds to memory address Ox3707. Which one of the following assembly language instructions corresponds to the machine instruction? Your answer: - BRp B ST RO, B ST RO, A BRnzp C

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
Assume that the state of the 8088’s registers and memory just prior to the executionof each instruction in problem 15 is as follows: * in photos*What result is produced in the destination operand by executing instructions (a)through (k)? *only h through k* (h) MUL DX(i) IMUL BYTE PTR [BX+SI](j) DIV BYTE PTR [SI]+0030H(k) IDIV BYTE PTR [BX][SI]+0030H
1. T/F - if (B)=006000 (PC)=003600 (X)=000090, for the machine instruction 0x032026, the target address is 003000.2. T/F – PC register stores the return address for subroutine jump.3. T/F – S register contains a variety of information such as condition code.4. T/F – INPUT WORD 1034 – This means Operating system should reserve 1034 bytes in memory5. T/F - In a two pass assembler, adding literals to literal table and address resolution of local symbol are done using first pass and second pass respectively.
Assuming the following MIPS assembly language code snippet is loaded into the memory of a MIPS-32 processor-based system starting at memory address 0x00400000. Fill the blanks on the right with the corresponding machine code in hexadecimal. Loop: sll $t1, $s3, 2 0x[a] add $t1, $t1, $s6 0x[b] lw $t0, 0($t1) 0x[c] bne $t0, $s5, Exit 0x[d] addi $s3, $s3, 1 0x[e] j Loop 0x[f] Exit: Note: Do NOT include '0x' and do NOT omit the leading '0's in your answers. Please show work by hand not just by running MARS and showing answers there please!!
Consider the following instruction:Instruction: Add Rd, Rs, RtInterperation: Reg[Rd] = Reg[Rs] + Reg[Rt] RegWrite MemRead ALUMux MemWrite ALUOp RegMux Branch a, What are the values of control signals generated by the control in Figure 4.2 for the above instruction? b, Which resources (blocks) perform a useful function for this instruction? c, Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d, which resources (blocks) produce no output for this instruction?
Write an assembly code to implement the y = (x1+x2) * (x3+x4) expression on 2-address machine, and then display the value of y on the screen. Assume that the values of the variables are known. Hence, do not worry about their values in your code. The assembly instructions that are available in this machine are the following: Load b, a Load the value of a to b Add b, a Add the value of a to the value of b and place the result in b Subt b, a Subtract the value of a from the value of b and place the result in b Mult b, a Multiply the values found in a and b and place the result in b Store b, a Store the value of a in b. Output a Display the value of a on the screen Halt Stop the program Note that a or b could be either a register or a variable. Moreover, you can use the temporary registers R1 & R2 in your instructions to prevent changing the values of the variables (x1,x2,x3,x4) in the expression. In accordance…
Please answer this question and provide the explanation Assume the values of %ecx is 0x00000005 and %edx is 0x00000003. What would be the value of %ecx and %edx after performing the following instruction? 0x5555555461a <+0>: leal (%ecx, %edx, 8), %edx %ecx = 0x00000005, %edx = 0x0000003A %ecx = 0x00000005, %edx = 0x00000018 %ecx = 0x00000005, %edx = 0x00000030 %ecx = 0x00000005, %edx = 0x00000003 %ecx = 0x00000005, %edx = 0x0000001D %ecx = 0x00000005, %edx = 0x00000040 %ecx = 0x00000055, %edx = 0x0000001D %ecx = 0x00000005, %edx = 0x0000002A %ecx = 0x00000005, %edx = 0x00000025 %ecx = 0x00000005, %edx = 0x00000035
Using the information below, in assembly language: x BYTE -2, -3, 2, 1 z WORD 3000h, 4000h, 5000h, 6000h y WORD -14, 32 bx starts with a value of 2222h, what is the hex value of bx when the following instructions execute in sequence? 1. mov bl, x 2. mov bh, [x+4]
The MSP430 can move/copy a byte or a word at a time using the instructions mov.b and mov.w respectively. In particular, the instructions mov.b &source_address, R4 mov.w &source_address, R4 copy the byte or word that resides at the given address (&source_address) to the given destination (the core register R4 in the CPU). Which of the following instructions are valid? (a) mov.b &0x1C03, R4 (b) mov.w &0x1C02, R4 (c) mov.b &0x1C00, R4 (d) mov.w &0x1C05, R4
Will upvote! Find the memory address of the next instruction executed by the microprocessor, when operated in the real mode, for the following CS:IP and 80286 register combinations: a. DS=2F2E & DX=9D64 b. CS=9F7A & IP=AB27 c. ES=DE21 & DI=D75F d. SS=FF5C & BP=92B8 e. DS=DC67 & CX=2FE8
A. Assume that the Instruction Pointer, EIP, contains 9610 and the assembly language representation of the instruction in memory at address 9610 is JB 175. If the flags are currently CF=0, ZF=0 and SF=1 what is the value of the EIP after the instruction executes? B. Assume that the Instruction Pointer, EIP, contains 15410 and the assembly language representation of the instruction in memory at address 15410 is JNS 189. If the flags are currently CF=1, ZF=0 and SF=1 what is the value of the EIP after the instruction executes? C. Assume that before the instruction is executed, the flags are CF=0, ZF=0 and SF=0 and the Registers have the values AL=0x35, BL=0x0F CL=0x25 and DL=0x78. What are the values of the flags after the instruction ADD AL,0x90 executes? D. The following instruction is executed. Assume that before execution, register R12 contains 0x85, R9 initially contains 0xC3, and the flags are ZF=0, SF=1, and CF=0. 0x indicates hexadecimal; do not include a 0x with your…
In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the contents of AX after executing the following programs? Assume that the initial content on the Carry Flag (CF) is one for all the calculations. You MUST clearly show ALL your steps in obtaining your final result for getting full and/or partial credit. Please present your final result in Hexadecimal format. (a) MOV CL,04H SHR AX,CL RET (b) MOV CL,04H RCR AX,CL RET