Q4:Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses.PipeDiameterAB250 mm200 mm400 mmBCBDLength1200 m600 m200 mEL.45mEL3m.BCEL. 3.0mDEL0.0m

Answered: Image /qna-images/answer/581cc3f4-9e39-4bbd-b817-87b7dde41fb7.jpg

Answered: Assuming f-0.020, determine the…

Engineering

Mechanical Engineering

Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The uniform beam is supported by two rods AB and CD that have cross-sectional areas 10 mm² and 15…

Q: raugue ng easures that may be taken to increase the resistance to fatigue of metallic materials. Ple…

A: Introduction: When a material is subjected to cyclic stresses and strains at high-stress…

Q: Find the equivalent spring constant of a uniform mild steel rod length of 2.5 m, cross-sectional…

Q: In the annual battle of the dorms, students gather on the roofs of Jackson and Walton dorms to…

Q: A projectile is launched with a speed vo= 29 m/s from the floor of a 4-m-high tunnel as shown.…

Q: Replace the force system with a single resultant force. Let F = [F] lb. ) Determine the location x,…

A: Given Force, F1 = 3500 lb F2 = 5500 lb F3 = 1750 lb Find Location, x

Q: The drag force, Fd, imposed by the surrounding air on a vehicle moving with velocity V is given by…

A: Given data:- Drag coefficient(Cd) = 0.28 Projected frontal area(A) = 24ft2 Air density(ρ) =…

Q: 0-3 rad/s Water Diameter 6ft Delta p=? 3. A circular tank (diameter 6 ft) filled with water is…

Q: A machine shaft supported on bearings 2 m apart is to transmit 180 KW at 200 rpm while subjected to…

A: The given information in the problem is listed below in the attached image:

Q: A wheel is mounted on a shaft (G= 80x10^9 N/m^2) of length 3 m and radius 1 cm. The wheel is rotated…

A: GivenG=80×109 N/m2L=3mr=1cm=0.01mθ=5degreeT=2.3s

Q: A wheel is mounted on a shaft (G= 80x10^9 N/m^2) of length 3 m and radius 1 cm. The wheel is rotated…

Q: etermine approximately the degrees of superheat of a steam at 150 kPa and 7.3709 kJ/(kg-K).

A: Given:Pressure, P=150 kPaSpecific entropy, s=7.3709 kJ/kg.K

Q: state kelvin statement of the second law of thermodynamics Please explain clearly

A: Kelvin-Plank statement of the second law of thermodynamics: Statement: "It is impossible for any…

Q: Air is compressed in a piston-cylinder assembly from p₁ = 25 lb/in², T₁ = 500°R, V₁ = 9 ft³ to a…

Q: A 5m³ tank contains saturated air at 25°C (Psat = 3.169 kPa) and 97 kPa. Determine the following:…

Q: For the 2D geometry shown in Fig.1, evaluate the shape factors F13 and F33 if F12-0.54. H 4 m 0 =…

A: Given, From the figure Radius, R=4+6=10 m Length of area 1, L1=6 m Length of area 2, L2=6 m Central…

Q: 1. If I want the 100-lb block to move with a constant acceleration of 5 ft/s² up the slope, what is…

Q: A hollow circular steel shaft with an outside diameter of 2.569, and a wall thickness of 0.388 in.…

A: GivenPart 1D=2.569int=0.388inT=292 lb-ftL=124inG=12000 ksiPart 2D=2.915int=0.437inT=239 lb-ftL=105…

Q: A turbocharged 6-cy, V-type diesel engine has an air consumption of 3000 kg/hr. per cylinder at…

Q: Two lbs of water vapor in a piston-cylinder assembly expands at a constant pressure of 350 lb/in²…

Q: following data resulted from a time study made on a horizontal milling machine: Mean manual effort…

A: When the time is taken without the allowances for any kind of operations then it is known as the…

Q: Refrigerant 134a expands in a piston-cylinder assembly from p₁ = 160 lb/in² and T₁ = 140°F to p₂ =…

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Determine the volume change, in ft3, when 1 lb of water, initially saturated liquid, is heated to…

A: Given:- Mass of water (m) = 1 lbsaturated liquid is being heated to saturated vapor at constant…

Q: OPERATIONS RESEARCH solve using the simplex solution (mixed constraints) show all the iteration show…

A: Given

Q: Determine the volume change, in ft3, when 1 lb of water, initially saturated liquid, is heated to…

Q: A girl weighing 604 N hangs suspended on the end of a rope 9.0 m. long. If a friend pushes her…

A: Given Weight, W = 604 N Angle = 38o Length, L = 9 m Find Lateral force, F…

Q: ... Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to…

Q: A refrigeration system operates on the reversed Carnot cycle. The minimum and maximum temperature…

Q: A pipeline 0.3 m in diameter divides at a Y into two branches of 200 mm and 150 mm in diameter. If…

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

Q: Air with dry bulb temperature of 25°C (Psat=3.169 kPa) and a wet bulb temperature of 15°C (Psat =…

Q: Determine the equivalent nodal forces for the axially distributed loading acting on the bar…

A: Solution: Given Data: bx=96-6x lb/in To Find: f1 and f2

Q: Explain the difference and/or similarities of Upfeed System and Overheadfeed System distribution of…

A: Upfeed system distribution of cold water- when water distributed directly from municipal pipe water…

Q: • The Precast T-Beam has the cross section shown. Determine its weight per meter of its length if it…

A: Given: Diameter of the cold formed steel: →d=20 mm And number of cold formed steel rods→n=8 So total…

Q: At the instant θ = 60∘, link CD has an angular velocity ωCD = 4 rad/s and an angular acceleration…

A: Given: Angular velocity of CD: →ωCD=4 rad/s Angular acceleration of CD: →αCD=3 rad/s2 And the…

Q: 4@4m 16 m b 12 kN 2 m 3 m

A: According to Bartleby QnA guidelines, “Since you have asked multiple question, I will solve the…

Q: Two and one half pounds of air (R=53.3) follow a polytropic process. At initial conditions the…

A: Given Initial temperature, T1 = 470oF Final temperature, T2 = 140oF Initial pressure, P1 = 85 psia…

Q: 1. Determine the force in members JI, IC, and CD of the truss. State if the members are in tension…

Q: For the objects shown in orthographic projection below, construct an isometric view in the space…

A: The isometric views for the given orthographic views are drawn in the space provided.

Q: 40 mm 40 mm

A: Given Data- A machine part subjected to loading as shown in fig Maximum normal stress in section AB…

Q: 60m 44m (2) (1) (3) 40m (4) 40m (5) 42m c) Find the flow discharge within the system. (6) 30m Q (2).…

A: Given data:- Diameter of pipe = 25 cm Length of pipe = 65 m The tank is open at the top. Find the…

Q: A piston-cylinder assembly contains 0.4 lb of air initially at a pressure of 30 lb/in² and a…

A: Given: mass, m = 0.4 lb T1 = 300 deg F P = 30 lbf/in2 Volume is doubled To find: Heat transfer Q12

Q: The shaft whose torque varies from 2000 to 6000 lb.in has a mean stress of 6,000 psi and a yield…

A: Given Data- Maximum torque =6000 lb.in Minimum torque =2000 lb.in Mean stress =6000 psi We have to…

Q: The bar has a constant width of 30 mm and a thickness of 10 mm. Determine the maximum normal stress…

A: Given data- A bar is given subjected to force system shown in fig We have to find maximum normal…

Q: Define The moment of inertia and determine it for T-section

A: Define the moment of inertia and by the defination find the moment of inertia for given T section.…

Q: 3. The blocks shown below slide together down the incline at the same acceleration. The coefficient…

A: Given Datamd=20kgmf=25kgθ=50°μd=0.5μf=0.1g=9.81 m/s2

Q: Heat exchanger has an overall coefficient of heat transfer for 0.50 kW/m²-degC. Heat loss is 11kW…

A: Given data: U=0.5 kW/m2.°CQ=11 kW∆Tm=15°C Need to determine the heat transfer area.

Q: A thin rod 5 mm diameter is held between two chucks 0.8 m apart and deflects 0.5mm under its static…

Q: Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Q4:
Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses.
Pipe
Diameter
AB
250 mm
200 mm
400 mm
BC
BD
Length
1200 m
600 m
200 m
EL.45m
EL
3m.
B
C
EL. 3.0m
D
EL
0.0m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q5: What is the diameter of smalle pipe, if the flow rate (30 lit/sec) ? ·S=0.6 D= Ans: 146.8 mm² 40cm D = 200mm D=?
ity of 25 m/s. 1 he pressures; Iy while the datum head at WJ A pipe of diameter 400 mm carries water L oints A and B are given as 29.43 Nfem” and 22.563 Nfcm respective B are 28 m and 30 m. Find the loss of head betweert A and B
A pipe experienced a total head loss of 15 m, determine thepressure difference from its starting point to discharge point inkPa.
The water is flowing througha pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 0.035 m /s. The section1 is 7500 mm above datunm and section 2i5 500 cm above datum. If the pressure at section 1 is 420 kPa, find the intensity of pressure at section 2.
CHOICES FOR PIPE 3: A. 733, B.373, C. 133, D. 311 Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes. AND PIPE 2
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
With the given pipe lengths, sizes and connections and if all pipes have an f=0.020. 1. which of the following most nearly gives the flow in pipe 2? a. 7 cfs b. 6 cfs c. 5 cfs d. 11 cfs 2. which of the following most nearly gives the head loss between B and C? a. 60 ft b. 100 ft c. 40 ft d. 80 ft with solution pls
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
A new cast-iron pipe 1200 ft long and 6 in. in diameter carries 1.3 cu. ft. per second. Determine the frictional loss.
A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute delivers water at a temperature of 150oF. If the slip is 7%, determine the discharge in a. discharge in Answer : __________________ lb/hrb. discharge in Answer : __________________ gpm
Determine the NPSH available to avoid the formation of cavitation in the system, water T° 13°C, pipe F°G°, Q=2.45 L/s, Re= 5.4 x 104. The efficiency of the motor will be 0.7, NPSHr = 3mca, the system has an average altitude of 3341 msnm, it is also known that the suction height is 0.80m. Suction pipe diameter 1 ¼”.