solve very fast in 15 min and I need a clear answer | dybala Assuming the criterion for suspended load transport is u-/v> 0.40 and for bed loadtransport is u-/v> 0.10, a rectangular channel (B=7 m, S, = 0.0005, n = 0.015, v= 1.186 x10 m/s). Assume uniform, steady flow and assume a spherical particle with d = 2.0 mmand neglect bed form roughness. Find the following by choosing the correct answer of thefollowing:1- If the settling velocity vss = 1m/s, the Reynolds number (Rep) isequal to:480.50O 579.111686.34O Non of them2- If the settling velocity vss = 1m/s, the drag coefficient (CD) isequal to:O 0.370.530.750.85

Diameter of particle=2mm Kinematic viscosity=1.186 *10-6 m2/s To find Reynolds number nd drag…

Assuming the criterion for suspended load transport is u-/v> 0.40 and for transport is u-/v> 0.10, a rectangular channel (B7 m, S, 0.0005, n = 0.015, 10 m/s). Assume uniform, steady flow and assume a spherical particle with de and neglect bed form roughness. Find the following by choosing the correct ans following: 1- If the settling velocity vss = 1 m/s, the Reynolds number (Rep) i equal to:

Assuming the criterion for suspended load transport is u-/v> 0.40 and for transport is u-/v> 0.10, a rectangular channel (B7 m, S, 0.0005, n = 0.015, 10 m/s). Assume uniform, steady flow and assume a spherical particle with de and neglect bed form roughness. Find the following by choosing the correct ans following: 1- If the settling velocity vss = 1 m/s, the Reynolds number (Rep) i equal to:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows uniformly in a rectangular concrete open channel that is 10 m wide at a depth of 3m. The channel slope is 0.0025. Using n = 0.013. Find the velocity, flow rate and the boundary shear stress.
Q.1 Above Figure represents floor of a hydraulic structures rested on fine gravel with seen dimensions ,The discharge value = 366 m° /sec while total water way =12m, silt factor f=l, Safe exit gradient for fine gravel = 1/5 Unified thickness of floor =2m .Check floor length, Find depth of sheet piles at u/s and d/s sides, check thickness of floor at A, B, C, D use Lane Theory
A rectangular channel is 6.3 m wide and has depth of flow of 1.7m. The slope of the channel bed is 1/1000. The material used to line the channel is known to have a Ch = 49m^(1/2) m/s. Calculate the mean velocity & discharge.
A triangular dam 12 m high and 8 m base width retains water 10m deep and has a vertical upstream side. Compute the maximum soilpressure at the base. Sp. gr. of concrete is 2.4a. 152.92 kPa b. 192.25 kPac. 122.34 kPa d. 129.95 kPa
A concrete pipeline is installed to deliver 6m3/sec of water between two reservoirs 17km apart, if the elevation difference between the two reservoirs is 12m, determine the required pipe size, if friction factor, f of Darcy-Weisbash h equation is 0.0135.
The channel consists of a smooth cement section (m = 0.109) and overflow regions on each side that contain light brush (m = 1.54). If the bottom of the channel has a slope of 0.0015, determine the steady volumetric flow when the depth is 2.5meters.
n = 0.016 The rectangular-shaped channel has the best hydraulic cross-section. It is laid on a slope of 0.0064 The channel has 16.98 m^3/s Determine the required width to achieve the critical condition.
Consider a farm irrigation ditch in a loam soil having the following dimensions: bottom width= 0.6 m, total depth, 0.5 m, side slopes= 1.5 horizontal to 1 vertical, and depth of water= 0.4 m. If the bottom of the ditch has a uniform slope of 2 m/km, and if the bottom & sides are kept smooth and free from weeds, what will be the mean velocity(m/s) of flow and discharge in m^3/s? Use n = 0.02. Find the shear stress at the watersurface, at half flow depth, and the canal bottom in N/m2 (or Pa). What is the shear velocity in m/sec?
A trapezoidal dam wherein the upstream side is vertically straight and has a width at the top of 4 m, height of the dam is 24 m, height of the water at the upstream side is 20 m, bottom is 24 m, and has a coefficient of friction of 0.8 Find the factor of safety against sliding. Please answer it ASAP and with FBD. Thank you so much.
Civil Q- An irrigation canal has been designed to have R = 2.5 m and S = 1.6 x 104. The sediment on the bed has a median size of 0.30 mm.Determine the amount of bed load using Einstein's method.Assume depth of flow and mean velocity of flow to be 2.8 m and 0.95 m/s, respectively.
A trapezoidal channel with side slope of 2H-1V has a flow rate of 180 m3/s and depth of 4 meters. The slope is 1m per kilometer. Determine corresponding bottom width in meters. The correct answer is 21.06 Pls show me the solution
Design a straight trapezoidal erodible channel that can carry a discharge of 12.5m^3/s using tractive force method based on the following information. The side slope is 1V:4H The bottom slope is 0.0015 The manning's roughness coefficient is 0.024 The critical shear stress as 7.2KN/m^2 Angle of repose is 23 Density of water 1000kg/m^3