At a point in a stressed body, the cartesian components of stress are oxx = 60 MPa, Oyy = -40 MPa, Ozz = 20 MPa, Txy = -40 MPa, Tyz = 20 MPa, and Txz = 30 MPa. Determine: (a) The principle stresses and their direction cosines. (b) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n. x) = 0,429 : cos (n. v) = 0,514: cos (n. z) = 0.743

At a point in a stressed body, the cartesian components of stress are oxx = 60 MPa, Oyy = -40 MPa, Ozz = 20 MPa, Txy = -40 MPa, Tyz = 20 MPa, and Txz = 30 MPa. Determine: (a) The principle stresses and their direction cosines. (b) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n. x) = 0,429 : cos (n. v) = 0,514: cos (n. z) = 0.743

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following: a. Maximum and minimum principal stresses b. Normal and shear stresses on plane AB
At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy= -40 MPa, sigma zz = 20 MPa, tau xy = -40 MPa, tau yz = 20 MPa, and tau xz = 30 MPa. Determine: (a) The principle stresses and their direction cosines. (b) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n, x) = 0.429 ; cos (n, y) = 0.514; cos (n, z) = 0.743
At a point in a stressed material, the major principal stress is 66 kPa compression and the minor principal stress is 34 kPa tension. (a) Use the Mohr’s circle to determine the shear and normal stress on a plane 45° ccw from the major principal plane. (b) Determine the stress combination acting on the plane 75° ccw from the major principal plane.
The stresses acting on element A in the web of a train rail are found to be ‘75 (MPa)’tension in the horizontal x-direction and ‘90 (MPa)’ compression in the verticaly-direction. Also, shear stresses of magnitude ‘40(MPa)’ act in the directions shown inthe figure.a) Draw Mohr’s circle for the state of stress.b) Determine the stresses (σx', σy' and τxy') acting on an element oriented at an angle‘D=-10 ˚’ from the horizontal. Show these stresses on a sketch of an elementoriented at this angle Note: If the angle D is positive, then the shear stress is in the direction shown onthe unit element figure; if it is a minus sign, then the shear stress is in theopposite direction shown on the unit element figure.
A force pair M is applied on a plane that makes an angle with the vertical to the beam of which cross-section is shown. Find the stress at D point.
Find the stress resultants N, V and M, draw the diagrams of the stress resultants (N,V,M). q = 8kN/m, F = 10kN
The major and minor principal stresses acting at a point in a stressed material are 80 psi compression and 20 psi tension. (a) Draw the Mohr’s circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stresses acting on a plane that is 30° ccw from the major principal plane.
Solve alll subparts b, c, d and e B) determine the principal plane (for σmax) in radians. C) Determine the shearing stress in a plane, which is 330 with the vertical (clockwise). D) determine the normal stress (in MPa) in a plane, which is 330 with the vertical (clockwise). E) determine the minimum values of θ (in radians) for which the normal stress is the equal to or less than 35.2 MPa.
At a certain point in a stressed body, the principal stresses are σx = 98 mPa and σy = -40 mPa. Determine σx on the plane whose normal are +23∘ and 23+90∘
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at the midspan. (MPa)
Determine total stress and effective stress at point A
Please calculate the stresses at points A, B, C and D for the given problem in the above figure.