AV 25.0 2 33.0 2 52.0 V 37.0 V 1. 42.0 2 Consider the circuit above. If AV = 175 volts, what is the current in amps through the circuit? NOTE: if the current is clockwise, give it a positive sign; if it is counterclockwise, give it a negative sign. Enter answer as a number with 3 digits right of the decimal. Do not include unit in answer.

AV 25.0 2 33.0 2 52.0 V 37.0 V 1. 42.0 2 Consider the circuit above. If AV = 175 volts, what is the current in amps through the circuit? NOTE: if the current is clockwise, give it a positive sign; if it is counterclockwise, give it a negative sign. Enter answer as a number with 3 digits right of the decimal. Do not include unit in answer.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter28: Direct-current Circuits

Section: Chapter Questions

Problem 28.9P: Consider the circuit shown in Figure P28.9. Find (a) the current in the 20.0- resistor and (b) the...

See similar textbooks

Similar questions

(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
Consider the circuit shown in Figure P28.9. Find (a) the current in the 20.0- resistor and (b) the potential difference between points a and b.
What is the equivalent resistor, in units of Ohm, between the terminals a and b if you replace R1 by 4 Ohm, R2 by 1 Ohm and R3 by 5 Ohm resistor? Your result must contain two decimal places. Maximum of 5% of error is accepted in your answer.
The LED requires a minimum current of 20.0 mA to light. Assuming that your battery is operating at 9.00 V, what would the resistance be if the LED just begins to light up when brought into contact with the end of your carbon resistor? [Answer in kΩ]
The switch is flipped over to position b and the circuit is allowed to reach electrostatic equilibrium. What is the measured voltage across C2 to 3 significant digits? *Answer 50v is incorrect
Answer the following 1. A voltage of 120V generates an IR drop across two resistors connected in series. If the voltage drop across R1 is 30V, what is the voltage drop across R2, in Volts? a) 80 b) 40 c) 100 d) 90 2. Three resistors R1, R2 and R3 of 20, 40 and 60 ohms are connected in parallel through the 120 V power line. What is the total current in the power line? a) 10A b) 12A c) 11A d) 15A 3. Resistors in a circuit are generally used to: a) increase the flow of the current b) decrease the flow of current c) avoid overvoltage d) decrease the power in the circuit
It's saying the 0.0399 is incorrect. The units is g/mol. Thank you for your help.
0.73 amps flow thru a 15 Ω resistor. How muxh voltage does the resistor use ? How much power is used?
A circuit with a resistance R=64 omega is connected to a battery with potential difference across the terminals of deltaV=9.5 V. Part (a) input an expression for the current passing through the circuit, I. Part (b) What is the current in milliamps, mA? Part (c) If the resistance of the circuit was increased by a factor of ten, Rnew =10R, what is the new current in milliamps, mA?
Light A has four times the power rating of light B when operatedat the same voltage. (a) Is the resistance of light A greater than, lessthan, or equal to the resistance of light B? Explain. (b) What is theratio of the resistance of light A to the resistance of light B?
What color code corresponds to a resistance of 234x10 5 10% with a temperature coefficient of resistance equal to 25x10 -6 /C o ?
Current=1A V_ab=-12V V_bc=21V 4d. What is the total rate at which electrical energy is dissipatate in R1, R2, and R3 resistors. 4e. What is the power outpur of the 26V battery? 4f. At what rate is the electrical energt being converted to other forms in the 10V battery? 4g. Show that power output of the 26V battery equals the overall rate of dissipation of electrical energy in the rest of the circuit?