Young's modulus=130 GPa Poisson's ratio=D0.5 Axial strain at mid depth ?
Q: An inverted differential manometer containing an oil of sp. gr. 0.9 is connected to find the differe...
A:
Q: A centrifugal pump is required to pump water t an open water tank situated 4 km away from the locati...
A: Given:L=4 kmd=0.2 mf=0.01v=2 m/sh=5 m
Q: 3,600° The instantaneous angular velocity of the crank Q2A is counterclockwise. Q2A = 1.5 in. Find t...
A:
Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load...
A:
Q: Objective 7 Level 1 4 m- A The jib crane is supported by a pin at C and rod AB. If the load has a ma...
A:
Q: A flywheel of centroidal radtus of gyration k ts rigidly attached to a shaft that can roll along par...
A:
Q: A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment...
A: Given data F=185N
Q: The stroke and cylinder diameter of a compression ignition engine are 250 mm and 150 mm respectivel...
A:
Q: Problem 2 Determine the total time t (in hrs.) required to fill the spherical tank with liquid whose...
A: Given:s=2.5m=400 Kg/mind=4 m
Q: diesel engine has a compression ratio of 15 and heat addition at constant pressure takes place at 6%...
A: Given:r=15cut-off takes place at 6% of stroke
Q: A horizontal beam AC is supported by a square bar BD. Assume that the pin placed at B is adequate to...
A:
Q: A bronze bar is fastened between a steel bar and aluminun bar as shown. Find the largest value of P ...
A: Given:As=480 mm2Ab=650 mm2Aa=320 mm2Es=200 GPaEa=70 GPaEb=83 GPa
Q: Find the resultant of two forces equal to 50N and 30 N acting at an angle of60°
A: Given Forces F1= 50 NF2= 30 NAngle = 60 To find Resultant
Q: Moment diagrams. 14. (a) A timber beam of rectangular section is to support a load of 20KN/M uniform...
A: As we only solve upto one question, we will solve the first one. Please resubmit the other question ...
Q: The gas constant R has the value 287 J/Kg * K for dry air. Using the ideal gas law (P = PdryRT): Fin...
A:
Q: determine stress amplitude and stress ratio
A:
Q: 9) Why projections are named first angle and third angle Denotes the quadrant in which the model is ...
A:
Q: The instantaneous angular velocity of the crank Q2A is 3,600° counterclockwise. Q2A = 1.5 in. Find t...
A:
Q: 7. Draw the crystallographic feature given below. a) [111] b) (220) c) (0110)
A: Given
Q: Determine the reactions and forces (internal loadings) for points A, B, C, D and E as shown in the f...
A: FBD of the system, Uniformly variable load along AB is converted to point load which acts at point ...
Q: 750 kg of dry saturated steam at a pressure of 160 N/cm2 is generated in a boiler per hour. The temp...
A: Given mass of the steam ms=750kgpressure in boiler P=160N/cm2=16barheat loss at the exit of boiler Q...
Q: 1.38 The right-angle bar is supported by a pin at B and a roller at C. What is the maximum safe valu...
A: Given:ζ=20,000 psid=34 in
Q: Specific speed of a kaplan turbine
A: Given; Kaplan turbine are the turbine which works on axial flow reaction. In this turbine water flow...
Q: In a ballistic test shown in Figure Q2, a bullet is shot with a velocity of 450 m/s where it pierced...
A: Given Data The velocity of the bullet is: vb=450 m/s The velocity of block A is: vA=1.5 m/s The vel...
Q: -d1 m. -d2m- C KAc N/m d,m KAB N/m A D La longitud no alargada del resorte AB es de 8 m. d1 = 7 m d2...
A:
Q: Find the equivalent torsional spring constant (up to two decimal points) of the system shown in the ...
A:
Q: find femperature, at the trißle point? Vapou pressure of liquid & Sofid ammoniay are respectivelcy g...
A: Write the expression for vapour pressure of liquid ammonia. lnP=14.15-3054T ...... (1) Write th...
Q: d,m|d, m d;m d,m y B d,m
A:
Q: Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep en...
A:
Q: The work required to compress a gas reversibly according to PV1.30 = C is 67,790 J if there is no fl...
A:
Q: Example 4. The damped motion of a vibrating particle is defined by the position vector 30 30 t+1 -l ...
A:
Q: hat is the resulting angle in radian with 2 decimal places if the complex number is 1+3
A: Given:z=1+3j
Q: Question: A man can swim at 4 ft/s in still water. He wishes to cross the 40-ft-wide river to point ...
A: r: river m: man g: ground Answer: speed of man: 4.86 ft/s angle: 13.42 degree
Q: If the pressures at the beginning and end of compression in an Otto cycle engine are 1 kg/sqcm and 8...
A: As per given We have to find the air standard efficiency
Q: During a 24-hour operation of a Diesel power plant, it consumed 200 gallons of 25oAPI fuel at 28oC w...
A:
Q: 8 m -5m 4 m 5 m 5 m 15 m 500 N In connection with the above figure, as an Engineer you have to repla...
A:
Q: 2. An Al alloy rod with 300 mm length and 10 mm in diameter is subjected to 5 x 10° N force at one o...
A:
Q: 4. You have three blocks of different dimensions b2(400mmx3000mm), b3(400mmx4000mm). Compute the str...
A:
Q: The equation of motion of a particle is s = 8t2 + 3t – 10, where s is in meters and t in seconds. Fi...
A: Given data, s= 8t²+3t-10 Need to find initial velocity
Q: =150 le F =80 1b.
A: Write the force F1 and Fr in vector form as follows, F1=80 j^FR=150cos120° i^+150 cos180°-130° j^+15...
Q: 4-6. The crowbar is subjected to a vertical force of P = 25 lb at the grip, whereas it takes a force...
A: Given Data The vertical force acting on the crowbar is: P=25 lb The force acting on the nail is: F=...
Q: Problem 1 For the beam in the figure below, assume E = 29,000 ksi and I = 600 in“ for the whole beam...
A: Since we only answer up to 3 subparts, we will answer the first 3. Please resubmit the question by s...
Q: A fixation plate (thickness 3 mm, width 40 mm) has a circular hole of radius 5 mm. The plate contain...
A:
Q: A steel solid shafting of 5.8 cm diameter and 5 m in length is subjected to heat from 300C to 1000C....
A: Given Temperature, T1 = 30oC T2 = 100oC Diameter, d = 5.8 cm Ther...
Q: Consider a vehicle moving at a velocity of 1,000 mps through air and hydrogen. The specific gas cons...
A:
Q: Calculate the maximum contact exposure rate at the side surface of a 10-foot wide railcar loaded wit...
A: THE “6CE” EQUATION It Is sometimes necessary to estimate the exposure rate which can be expected fro...
Q: The tractor-trailer unit is moving down the incline with a speed of 4.3 mi/hr when the driver brakes...
A: Answer: The percent increase in the "hitch-force component which is parallel to the incline" compare...
Q: Determine the velocity of block A if end F of the rope is pulled down with a speed of vF= 7m/s.
A:
Q: If the length of a column is doubled, the critical load becomes ?
A:
Q: Find the coordinate direction angles ( α 1 , β 1 , γ 1 ) of the force F1 so that the resultant force...
A:
Step by step
Solved in 2 steps with 1 images
- A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
- A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
- The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.An element of aluminum is subjected to tri-axial stresses. Calculate the strains in the element in x, y, and z directions lithe stresses axayand az are -2000 psi, 3500 psi, and 2700 psi, respectively. Assume E = 10,000 ksi and v = 0.33. Also, find the unit volume change of the element.
- A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?