B/ A four fifth meter long steel pipe has an inside and outside diameter of 24 mm and 30 mm respectively, is subjected to a compressive force of 60 kN and the pipe length compressed by 0.3 mm. Determine the compressive stress and the compressing percentage.

B/ A four fifth meter long steel pipe has an inside and outside diameter of 24 mm and 30 mm respectively, is subjected to a compressive force of 60 kN and the pipe length compressed by 0.3 mm. Determine the compressive stress and the compressing percentage.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 49PQ

See similar textbooks

Related questions

Q: A 61 cm long copper wire is clamped at one end and a stone weighing 2.2 kg is attached to the other…

Q: A 20 g rectangle block of aluminium is 35 cm by 45 cm by 15 cm when unstressed. A force is applied…

A: Given information: The mass of the rectangle aluminum block (m) = 20 g = 0.02 kg The dimensions of…

Q: What is the maximum load that could be suspended from a copper wire of length 1.00 m and radius 1.08…

Q: A horizontal aluminum rod 3.1 cm in diameter projects 4.6 cm from a wall. A 940 kg object is…

A: Given : Diameter of horizontal aluminum rod, d = 3.1 cm = 0.031 m Radius of the horizontal aluminum…

Q: a) Sketch a stress-strain diagram for a metal indicating the proportional limit, yield point,…

Q: Assume a person's mass is 54.0 kg and each of her shoes has an area of 195 cm². F on her feet if her…

Q: Q2.9/ A copper wire with a circular cross section of a diameter (d31.2 mm) was cast by a force of…

A: From the question, it is given that- Force on copper wire: F = 90 N Diameter of copper wire: d = 1.2…

Q: What hanging mass will stretch a 2.0-mm-long, 0.59-mmmm-diameter steel wire by 1.2 mmmm ? The…

Q: A horizontal aluminum rod 4.7 cm in diameter projects4.4 cm from a wall. A 1100 kg object is…

Q: 1. A steel wire of length 4.7 m and cross section 3.0 x 10 m2 stretches by the same amount as a…

Q: A 1.4 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.5 x…

Q: A solid copper cube has an edge length of 88.3 cm. How much stress must be applied to the cube to…

A: Original length (L) = 88.3 cm New length (L') = 88 cm

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A: Write the given values with the suitable variables. P=250 kN=250×103 Nb=0.12 md=0.05 mt=0.003 m…

Q: 57. The drawing shows a 160-kg crate hanging from the end of a steel bar. The length of the bar is…

A: Mass of the crate, The length of the bar, The cross-sectional area of the bar, The shear…

Q: 20. The experimentally determined Young's modulus for brass is 9.0 × 10^10 Pa. A brass bar…

Q: A rectangular piece of wood, 50 mm x 100 mm in cross-section is used as a compression block as shown…

Q: A solid copper cube has an edge length of 86.9 cm. How much stress must be applied to the cube to…

Q: A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a diameter…

Q: Human bones have a Young's modulus of 1.5 x 1010 Pa. The bone breaks if stress exceeds 1.5 x 10° Pa.…

Q: A horizontal aluminum rod 4.8 cm in diameter projects 5.3 cm from a wall.A 1200 kg object is…

Q: A solid copper cube has an edge length of 86.9 cm. How much stress must be applied to the cube to…

A: Write the given values with the suitable variables. L1=86.9 cmL2=86 cmk=1.4×1011 N/m2 Here, L2, L1,…

Q: A 0.900 m-long metal wire has a circular cross section of diameter 0.950 mm. One end of the wire is…

Q: Max (mass = 15 kg) is hanging from one end of a 13-m long bungee cord that has its other end fixed…

Q: N/m The young's modulus of a material whose elastic strain and stress are 1.45 and 108.96 N/m2…

Q: Two cylindrical rods, one steel (Y = 2.00×10" Pa) and the other copper (Y = 1.10×10" Pa), are joined…

A: SOlution: Given that Steel, Y = 2x1011 Pa copper, Y = 1.1x1011 Pa Steel, L =1.3 m Copper ,L =2.6 m…

Q: A solid copper cube has an edge length of 89.9 cm. How much stress must be applied to the cube to…

A: The ratio of volumetric stress with volumetric strain is defined as the bulk modulus. To solve the…

Q: A solid copper cube has an edge length of 81.6 cm. How much stress must be applied to the cube to…

A: Given: L=81.6 cmL'=81.0 cmB=1.4*1011 N/m2

Q: A solid copper cube has an edge length of 85.9 cm. How much stress must be applied to the cube to…

A: Given: length of cube l = 85.9 cmfinal length =86cmchange in length ∆l = 86-85.9 = 0.1 cmBulk…

Q: Q4) A force of magnitude F = 62 × 10° N is applied perpendicularly to the steel rod of radius 9.5 mm…

A: Given data The magnitude of the force is F = 62 x 103 N The rod's radius is r = 9.5 mm. The length…

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

A: Given: Length of each beam, L=4 m Area of cross-section,A=7.5×10-3 m2 Load, W=4.5×104 N Young's…

Q: c) Table 1(c) shows the information of materials A and B. Compute the maximum stress that is applied…

A: Given: tensile stress σa = 13 MPamaterial A:σc = 240 MPa2c = 2.4*10-2 mmρt=1.2*10-4 mmmaterial B:σc…

Q: solid copper cube has an edge length of 81.3 cm. How much stress must be applied to the cube to…

A: Given Initial length l1 = 81.3 cm = 0.813 m Final length l2 = 81 cm = 0.81 m Bulk modulus B =…

Q: 2.47 The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the…

Q: A horizontal aluminum rod 3.0 cm in diameter projects 3.9 cm from a wall. A 870 kg object is…

A: Given:- Diamtere of the rod = 3.0 cm The radius of the rod is = 3/2=1.5 cm =1.5 X 10-2 m Length of…

Q: B43 (a) For moderate loads, most metals are elastic. What is meant by the term clastic? (b) The…

A: Part (a) When a load is applied on a metal upto a certain limit, then after removing the load, it…

Q: c) A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

Q: 20. A 20 cm cylindrical brass rod with diameter 6 cm is held vertically on its one circular flat…

Q: For a bronze alloy, the stress at which plastic deformation begins is 295 MPa and the modulus of…

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

A: Y=F/A∆L/L∆L=FLAY=4.9×104 N4.0 m9.1×10-3 m2210×109 N/m2=0.10×10-3 m1 mm10-3 m=0.10 mm

Q: For a LEHI material, the principal plane stresses and associated strains in a plane at a point are…

Q: A 1.0 x 10-3 kg spider is hanging vertically by a thread that has a Young’s modulus of 4.5 x 109 N/m…

Q: A horizontal aluminum rod 3.4 cm in diameter projects 7.0 cm from a wall. A 810 kg object is…

A: Answer:- Given Shear modulus (G) = 3 × 1010 N/m2 Length (L) = 7 cm =7× 10-2 m Diameter of rod (d)…

Q: *69. ssm A 1.0 × 10-3-kg spider is hanging vertically by a thread that has a Young's modulus of 4.5…

Q: A solid copper cube has an edge length of 89.6 cm. How much stress must be applied to the cube to…

A: The stress that must be applied to the cube is 2.726 x 109 N/m2

Q: A solid copper cube has an edge length of 93.8 cm. How much stress must be applied to the cube to…

A: Given Initial length of the copper cube is li=93.8 cm=0.938 m Final length of the copper cube is…

Q: A solid copper cube has an edge length of 89.8 cm. How much stress must be applied to the cube to…

Q: Stress and strain 3. A brass rod with a length of 1.40 m and a cross- sectional area of 2.00 square…

A: Given that:- Pulling force applied on each end=F=4×10^4N

Q: In her gymnastic routine, Regina dismounts from the uneven-parallel bars and lands straight-legged…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

B/ A four fifth meter long steel pipe has an inside and outside diameter of 24 mm and 30 mm
respectively, is subjected to a compressive force of 60 kN and the pipe length compressed by
0.3 mm. Determine the compressive stress and the compressing percentage.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
A spring 1.50 m long with force constant 475 N/m is hung from the ceiling of an elevator, and a block of mass 10.0 kg is attached to the bottom of the spring. (a) By how much is the spring stretched when the block is slowly lowered to its equilibrium point? (b) If the elevator subsequently accelerates upward at 2.00 m/s2, what is the position of the block, taking the equilibrium position found in part (a) as y = 0 and upwards as the positive y-direction. (c) If the elevator cable snaps during the acceleration, describe the subsequent motion of the block relative to the freely falling elevator. What is the amplitude of its motion?
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?
Review. A wire of length L, Youngs modulus Y, and cross-sectional area A is stretched elastically by an amount L. By Hookes law, the restoring force is kL. (a) Show that k = YA/L. (b) Show that the work done in stretching the wire by an amount L is W=12YA(L)2/L.
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
Use the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46