B Hinge 2 m 2m 2m

Q: Problem 2 Normal Distributions A lake has one input stream with a flow rate of 4 m/min. The value of...

A: Given that Flow rate Q= 4 m3/min Mean Value μ= 10grams/m3 Standard Deviation σ'=2 grams/m3   a) Mean...

Q: The milling machine is programmed so that during the interval of time from to the position of its he...

A: Given, Position function of the head: st=4t-2t2 here, s: position in inches t: time in seconds   The...

Q: The value of compression index (cc) for a remoulded sample whose liquid limit is 40% will be

A:

Q: situation 2: The velocity of a bobsled is v = 10t ft/s. When t =2s, the position of the sled is s =2...

A:

Q: A three hinged symmetrical parabolic arch of span 20 m and rise 5 m carries a uniformly distributed ...

A:

Q: A backward tangent having a slope of 7% intersects the forward tangent having a slope -4% at station...

A:

Q: abaight Q4. A cor js moving yood at 16 m/s.t js accelesatid Lat 10 m/2. Whot will be its 4velocity s...

A: given  initial velocity of car = V1 = 16 m/s acceleration of car = a = 10 m/s2  given time interval ...

Q: Calculate the axial compressive stress in the column due to a concentric load of 900 kN. а. 336 MPa ...

A:

Q: Q2: Determine the magnitude and direction of the friction force which the inclined plane exerts on t...

A:

Q: The value of coefficient of permeability (in cm/s) of a uniformly graded sand of size D10 = 0.15 cm ...

A: This question is related to Permeability from geotechnical engineering.

Q: Finding Reachon fa VAt Vy = 34+(60(442.7)+ fx6x 18 =490KN. %3D Y*9.7= 5778+91.8+1346-7 らこ 207.87 And...

A:

Q: A rock is thrown upward at a speed of 13.61 m/s. How long will it take to reach its highest point? t...

A:

Q: Example 24.31. Determine the ultimate net bearing capacity of the circular footing shown in Fig. 24....

A:

Q: Calculate the gravitational potential energy of a 10.5 kg box on a shelf 5.0 m above the floor. Assu...

A: Introduction : The given question is related with mechanics topic . We are provided with value of ma...

Q: Aggregates from two stockpiles, A and B having coarse aggregate angularity (crushed faces) of 40% an...

A: Consider the given data For stock pile A percentage crushed faces =40% For stock pile B percentage c...

Q: Design a W section tor member CD of the truss shown in the figure 4.5. Use A 36 steel and assume the...

A: We have to design a W section to member CD of the truss shown in the figure using A36 steel and assu...

Q: If the distance two places on the map is 12cm, with the map scale of 1:2,000,000,what is the ground ...

A: Given data, Map scale = 1:2,000,000 Distance of 2 places on map = 12 cm

Q: FN= 78 SN= 66

A: This question is related to structure analysis. In this question using force equilibrium equation we...

Q: What is the minimum bolt diameter required in mm.

A: For shearing of rivets P = ζA 60x1000 = 822x14πd2   d = 21.58 mm

Q: What is the main objective of conducting a transportation project evaluation?

A: The main objective of a transportation project evaluation is to furnish the appropriate information ...

Q: A solid circular steel column is 3 m long and 0.4 m in diameter. It carries a oad of 50 MN. The modu...

A: (i) Find the stress in the column. (ii) Find the strain in the column.

Q: The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75kN/m A....

A: W 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m ROPERTIES OF W 14 * 132 A = 17...

Q: Tabulated results for fineness of cement are shown below. Which tabulation/tabulations contorms with...

A:

Q: 2 – 22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d

A:                 STEP1:GIVENINFORMATIONi.Width(b)=300mmii.EffectiveDepth(d)=537.50mmiii.Diameterofba...

Q: PI Lt PC C D Forw tangen jent R PT 12

A: What has to be determined in this question. 

Q: A rock is thrown upward at a speed of 13.61 m/s. How long will it take to reach its highest point? t...

A:

Q: Describe the major differences between Production Risk and Project Risk

A: Project Risk: It is an uncertain situation that can impact the project objective and achievement.  ...

Q: Pasig River EXISTING STRUCTURE EXISTING STRUCTURE PSG COMPOUND Croek Creek 2 SITE DEVELOPMENT PLAN C...

A: Plan detail of  a site is given. From the given detail various important factors which comes out  fr...

Q: What's the factors that causes zero and sensitivity drifts

A: All calibration of any instrument is considered valid under standard conditions of temperature, pres...

Q: Situation 1: The position of a particle along a straight line is given by s = (t3 - 9t2 + 15t) ft , ...

A:

Q: Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x...

A:

Q: A man's eyes 1.75 m. above sea level can barely see the top of a lighthouse which is at a certain di...

A:

Q: A rock is thrown upward at a speed of 13.61 m/s. How long will it take to reach its highest point? t...

A: Given data, Initial velocity u = 13.61 m/s

Q: An engineer who was awarded a Php450,000 contract to install the machineries of an oil mill failed t...

A: Given data, Contract price C = Php450,000 Penalty for 1st 10 days = 0.25% of C Penalty for next 10 d...

Q: Problem 2 -1 The single 200 mm x 10 mm steel plate is connected to a 12-mm thick steel plate by four...

A: We have to determine the value of P in all possible modes of the failure and the safe value of P tha...

Q: F=90 N 900 mm A 500 mm

A:

Q: From the given data of a differential leveling as shown in the tabulation: STA. B.S. H.I. F.S. ELEV....

A:

Q: ully welded together. The PL16×380 and PL12X500 for the

A: the flexural strength is given by F =PLbd2where . p = load on beam            L = length         b =...

Q: For the beam shown in the figure, draw the influence lines for (a) reaction at A, (b) shear just t...

A: We have to determine reaction at A and shear just to the right of A and moment at A, and moment at D...

Q: A Cylindrical soil sample of 7.5 cm height and 3.75 cm diameter has been prepared at the shrinkage l...

A:

Q: A PL x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. Th...

A: We have to determine the value of design strength Pu based on gross area and also based on effective...

Q: create (P,L,E,A,N,U,G) 2D drawing using lines, circles, curves,etc

A: Here is your drawing

Q: Situation 5 Block A weighing 250 N rests on top of block B whose weight is 175 N. The coefficient of...

A:

Q: A road measures 20 cm on a map and 50 km on ground. What is the map scale?

A: Given data : Ground distance=50 km Map distance=20 cm   Required : Map scale

Q: . Using the force method of analysis, determine the force in each member of the Truss shown in Q. 2....

A:

Q: 26. What displacement would an accumulator have to be in order to supply 10 gallons of fluid between...

A:

Q: 6. The figure (next page) shows an experimental set-up for testing the bending capacity of a wood cr...

A:

Q: A square hollow steel strut with a wall thickness, ti = 10 mm is pin connected to two gusset plates,...

A: We will Divide Load by effective area to find stresses.

Q: The value of coefficient of permeability (in cm/s) of a uniformly graded sand of size D10 = 0.15 cm ...

A:

Q: A rock is thrown upward at a speed of 13.61 m/s. How long will it take to reach its highest point? t...

A: Given data : The initial velocity=U U=13.61 m/s The value acceleration due to gravity=g g=-9.81 m/s2...

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.