(B) // The straight beam with distribution load as shown in figure B is simply supported by a pin at A and a rod attached to point C. Determine the shear stress in (a) the pin at A and (b) the pin at C. Assume the pins have diameters of 0.6 in known the distribution load q = 1.4 kip/ft 2ft -3 ft 1.5 ft- TTTIT

(B) // The straight beam with distribution load as shown in figure B is simply supported by a pin at A and a rod attached to point C. Determine the shear stress in (a) the pin at A and (b) the pin at C. Assume the pins have diameters of 0.6 in known the distribution load q = 1.4 kip/ft 2ft -3 ft 1.5 ft- TTTIT

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.2P: A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN...

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
A short length of a C 200 × 17.1 channel is subjected to an axial compressive force P that has its line of action through the midpoint of the web of the channel (see figure part a). (a) Determine the equation of the neutral axis under this loading condition. (b) If the allowable stresses in tension and compress ion are 76 MPa and 52 MPa respectively, find the maximum permissible load (c) Repeat parts (a) and (b) if two L 76 × 76 × 6.4 angles are added to the channel as shown in the figure part b. See Table F-3(b) in Appendix F for channel properties and Table F-4(b) for angle properties.
A ship's spar is attached at the base of a mast by a pin connection (see figure). The spar is a steel tube of outer diameter d2= 3.5 in. and inner diameter d1= 2.8 in. The steel pin has a diameter d = 1 in., and the two plates connecting the spar to the pin have a thickness t = 0.5 in. The allowable stresses are compressive stress in the spar. 10 ksi: shear stress in the pi n, 6.5 ksi: and bearing stress between t he pin and t he connecting plates, 16 ksi. Determine the allowable compressive force Pallowin the spar.
A short column constructed of a W 12 × 35 wide-flange shape is subjected to a resultant compressive load P = 25 k having its line of action at the midpoint of one flange (see figure). Determine the maximum tensile and compressive stresses d1and d2., respectively, in the column. Locate the neutral axis under this loading condition. Recompute maximum tensile and compressive stresses if a C 10 × 15.3 is attached to one flange, as shown.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
A circular aluminum tube with pinned ends supports a load P = 18 kN acting at a distance e = 50 mm from the center (see figure). The length of the tube is 3.5 m, and its modulus of elasticity is 73 GPa. If the maximum permissible stress in the tube is 20 MPa, what is the required outer diameter d2if the ratio of diameters is to be d1/ d2= 0.9?
A bridge girder A B on a simple span of length L = 14 m supports a distributed load of maximum intensity q at m id-span and minimum intensity q/2 at supports A and B that includes the weight of the girder (sec figure). The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q based upon (a) an a I lowable bending stress tra]Um = 110 M Pa and (b) an allowable shear stress r ,. = 50 M Pa.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.