A l-m-long rectangular beam is attached to a 2-m-long circular shaft and loaded as shown in the figure below. Calculate the maximum normal and shearing stresses at points A, B, and C. 600 N 6 ст 2 cm A 10 kN

A l-m-long rectangular beam is attached to a 2-m-long circular shaft and loaded as shown in the figure below. Calculate the maximum normal and shearing stresses at points A, B, and C. 600 N 6 ст 2 cm A 10 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.10.10P: A hollow steel box beam has the rectangular cross section shown in the figure. Determine the maximum...

See similar textbooks

Related questions

Q: 3.45 A4-ft-long tube with the cross section shown in the figure is made of alumi- num. Find the…

Q: 150 B D C St Al 50 30 300 N.m 600 500

A: Applied torque, T=300 N-m Diameter of the aluminum section, dAl=50 mm Diameter of the steel section,…

Q: A wood beam reinforced by an aluminumchannel section is shown in the figure. The beam hasa cross…

A: According to the problem, n=EaEw =6 Here, n is the ratio of Young's Modulus, Ea is the Young's…

Q: A steel pipe with an outside diameter of 4.13 in. and an inside diameter of 3.69 in. supports the…

Q: A concentrated load of P = 19 kN is applied to the upper end of a pipe with length L = 5 m. The…

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36…

Q: torsional deformation and shear stress due to an applied force in a door handle design.

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

Q: 10 kN 3 kN/m 100 mm 200 mm B 1.5 m 1.5 m 2.2 m

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in figure below. Ea…

Q: torque that will cause a maximum shear stress of 10 000 psi. Use G = 4x 106 psi for aluminum. e-4…

A: Solnn:- in a given figure Sear stress=10000 psi G= 4×10^6 psi Now, enclosed area Am= π\2 × r^2 +…

Q: n. The end chord of a timber truss is framed into the bottom chord as shown in Figure (3.14).…

Q: A simple beam is loaded as shown in the figure below If the load P 120 kN determine the maximum…

A: Normal stress will be maximum at cross section 'B'Net normal stress = Normal stressaxial+Normal…

Q: 4 ft Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure.…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: What the maximum stresses in the stepped shaft composite of two materials steel and Aluminum that…

A: Given Data torque=300 N.m Gs=82 GPa Gal=27 GPa Polar moment of inertia,

Q: Tsy

A: Given Data⇒ σx=60 MPaσy=50 MPaζxy=50 MPa

Q: Example Fig. 4.19. If permissible stress is 150N/mm2, find its moment of resistance. Compare it with…

A: Area of I section = 7040 mm2 moment of inertia of I section; I = (bd3/12) - (b1d13/12)…

Q: A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kW hrough a…

Q: The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 50 m long. α = 11.7 ×…

A: Temperature, T1= 15∘C Rail length, L= 50 m α= 11.7×10-6/∘C E= 2.3×105 N/mm2 Expansion allowance, ∆=…

Q: A beam of channel section (as shown in the figure) is subjected to a shear force 50 kN. Draw the…

A: S=50 KN Now moment of inertia passing through N.AI=112×b×h3I=112×.06×.13=5×10-6 m4

Q: A solid bar having a diameter 150 mm is to be replaced by a square tube having a cross-sectional…

Q: For the system shown in the figure, find the maximum internal shear force in kN. Hint: you will need…

Q: Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure. Note…

Q: 1. Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure.…

Q: . Determine the shear stresses along sections A-A, B-B, C-C and D-D. b. Plot the shear stress…

Q: Since the bending safety stress Bem = 10 MPa and shear safety stress Bem = 600 kPa of the…

A: Given, Safe bending stress ,σb =10 MPa Safe shear stress , ζs=600 KPa

Q: Que 5.6. A crane hook trapezoidal horizontal cross-section is 50 mm wide inside and 30 mm wide…

Q: Q2) A rectangular beam 120mm wide by 400mm deep is loaded as shown in the figure. Find "P" to cause…

A: Any action that can change the state of motion is force. Force is described by its magnitude, point…

Q: For the beam and loading shown in the figure below, determine: 1- The normal and shearing stresses…

A: Part 1 From fig we can say that the forces that play a vital role to form normal and shear stress…

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

A: GIVEN DATA- A STEPPED SHAFT GIVEN WE HAVE TO FIND MAXIMUM SHEAR STRESS IN SHAFT

Q: A hollow steel shaft used in a construction auger has outer diameter d2 = 7.8 in. and inner…

A: Given data:

Q: Calculate maximum compressive strain on circular beam with an outside diameter of 80mm and wall…

Q: 2. A sign is supported by a pipe (See figure) having outer diameter Dand inner diameter d. The…

Q: Q1: The thin-walled single cell beam shown in Fig.1 has been idealized into a combination of direct…

Q: An automobile engine supplies power, P= 190 hp, at a rotational speed of 4000 rpm to a driveshaft.…

A: Given data: Power developed = P = 190 hp Speed = N = 4000 rpm Tallow = allowable shear stress = 5…

Q: A (14-ft long) simply supported timber beam subjected to shear force of (3-kip) as shown in Figure.…

A: Given data as per question Shear force on beam =3 kip Length of the beam =14 ft Moment of inertia…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

Q: 1. Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure.…

Q: A hollow circular shaft has an external diameter of 120 mm and the internal diameter is…

A: Given Data External radius, R=60 mm Internal radius, r=3/4(60 mm)=45 mm SHear stress, 36MPa G=85 MPa…

Q: A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50…

A: Given Data, T = Torque transmitted by the solid shaft = 600 Nm = 600 x103 Nmm ?max= Maximum shear…

Q: For the framc shown in the figure, Find the normal and shear stresses based on the following…

A: Given: The diameter of the pin at A, d = 10 mm The diameter of the pin at C, D = 15 mm

Q: A hydraulic punch press is used to punch a slot in a 0.30-in.-thick plate, as illustrated in the…

A: Given:Thickness of plate, t=0.3 inshear stress at plate, τ=36 ksid=1.25 ina=2.25 in

Q: A hollow shaft of outer radius 140 mm and inner radius 125 mm is subjected to an axial force and a…

A: Outer radius of hollow shaft , R=140 mmInner radius of hollow shaft , r=125 mmaxial force, F=68…

Q: A round shaft of diamater D = 65 mm with a groove cut into it where the diameter decreases to d = 50…

Q: 4 ft- 4 ft– 500 lb A 4 ft C BA 2 ft 2 ft 4 ft 500 N D

Question

A l-m-long rectangular beam is attached to a 2-m-long circular shaft and loaded as
shown in the figure below. Calculate the maximum normal and shearing stresses at
points A, B, and C.
| 600 N
б ст
2 cm
A
B
10 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Derive the following formula for the distance e from the centerline of the wall to the shear center S for the hat section of constant thickness shown in the figure: Also, check the formula for the special case of a channel section (a = 0).
A wood box beam is constructed of two 260 [mm] x 50 [mm] boards and two 260 [mm] x 25 [mm] boards (sec figure). The boards are nailed at a longitudinal spacing. b=100 [mm]. If each nail has an allowable shear force F=1200 [N], and Vmax=10652.6 [N]. What is the magnitude of the shear stress at the midpoint of either left or right plank?
If a beam has a rectangular cross section of heigh 300mm and width 60mm. In one cross section plane the beam experiences a shear force of 2x10^6 N. How do I work out the; 1 - shear stress at neutral axis 2 - the bottom surface 3 - 20mm from the top surface
A wood box beam is constructed of two 260 [mm] x 50 [mm] boards and two 260 [mm] x 25 [mm] boards (sec figure). The boards are nailed at a longitudinal spacing. b=100 [mm]. If each nail has an allowable shear force F=1200 [N], and Vmax=10652.6 [N]. What is the magnitude of the shear stress at the midpoint of either vertical plank?
A hollow steel box beam has the rectangularcross section shown in the figure. Determinethe maximum allowable shear force V that may acton the beam if the allowable shear stress is 36 MPa.
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
Consider the beam section below where fc’ = 30 MPa, Es = 200 GPa, determine the bending stress of the steel section if M=180 KN-m in MPa. Express your final answer in two decimal places.
A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) on a section 2.63 m from A if P = 5111 N, W = 2076 N/m, a = 0.75 m, b = 1.16 m, c = 1.03 m, L = 84 mm and h = 208 mm. Round off the final answer to two decimal places.
simply supported wood beam with overhang is subjected to uniformly distributedload q. The beam has a rectangular cross section with width b = 200 mm and height h= 250 mm. Determine the maximum permissible value q if the allowable bendingstress is eall= 11 MPa, and the allowable shear stress is Tall= 1.2 MPa.
A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress (in Pa) at a point 11 mm from the top of the of the beam on a section 2 m from A if P = 5329 N, W = 2383 N/m, a = 1.23 m, b = 2.23 m, c = 1.3 m, L = 67 mm and h = 230 mm. Round off the final answer to two decimal places.
Rectangular section and width given in the figureThe bending safety stress of the beam with b = 150 mm em = 10 MPa,Since shear safety stress em = 600 kPa,In order that the stresses that will occur do not exceed the safety stress valuesWhat should be the minimum height h of the beam section.
The cross-sectional beam shown in the figure is subject to a maximum shear stress of 35 ksi, due to a shear force V. Determine the shear stress at points B and C, each segment of the beam has a thickness of 15mm.