b) The torques shown in Fig. Q1(b) are exerted on pulleys A, B, C and D. Knowing that each shaft is solid, 120 mm long and made of steel with Modulus of Rigidity of 77 GPa and Modulus of Elasticity of 70 GPa i) Compute the angle of twist between A and C with the aid of free body diagrams. i1) State the direction of the twist (either clockwise or counterclockwise) for question Q1(b)i. 120 N-m 90 N-m 60 N-m 20 mm C 15 N-m 15 mm B 10 mm A

b) The torques shown in Fig. Q1(b) are exerted on pulleys A, B, C and D. Knowing that each shaft is solid, 120 mm long and made of steel with Modulus of Rigidity of 77 GPa and Modulus of Elasticity of 70 GPa i) Compute the angle of twist between A and C with the aid of free body diagrams. i1) State the direction of the twist (either clockwise or counterclockwise) for question Q1(b)i. 120 N-m 90 N-m 60 N-m 20 mm C 15 N-m 15 mm B 10 mm A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stepped shaft shown rotates at 480 rpm. Knowing that r = 0.2 in. and using figure 3.28, determine the largest torque T that can be transmitted without exceeding an allowable shearing stress of 7000 psi.
A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter steel bolts on a circle of diameter 400mm and six 10mm diameter steel bolts on a circle of diameter 300mm. Determine the number of 10mm diameter steel bolts that must be used on the 400mm bolt circle of the coupling to increase the torque capacity to 15kN-m.
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
The design specifications for the gear-and-shaft system shown require that the same diameter be used for both shafts and that the angle through which pulley A will rotate when subjected to a 2-kip·in. torque TA while pulley D is held fixed will not exceed 7.5°. Determine the required diameter of the shafts if both shafts are made of a steel with G= 11.2 × 106 psi and τall= 12 ksi.assuming that both shafts are made of a brass with G= 5.6 × 106 psi and τall= 8 ksi.
Two solid steel shafts, each 30 mm in diameter, are connected by the gears shown in the figure. Knowing that G = 77.2GPa, determine the angle through which end A rotates when a couple of magnitude T = 200Nxm is applied to A.
Two shafts having the same length and material are joined in series. If the ratio of the diameter of the first shaft to that of the second shaft is 2, then the ratio of the angle of twist of the first shaft to that of the second shaft is:
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm diameter steel bolts must be used on a 200-mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A single solid circular shaft 400 mm diameter running at 250 RPM, is to be replaced by two hollow circular shafts of equal size running at 150 RPM and developing 50% additional power. The internal diameter of hollow shaft may be taken as one third of their external diameters. If the working stress of the new shaft is 30% greater than that of the former, find the external and internal diameter of hollow shafts.
A pulley is connected to a power transmission shalt of diameter d by means of a rectangular sunk key of width w and length I. The width of the key is taken as d/4. For full power transmission, the shearing strength of the key is equal to the torsional shearing strength of the shal: The ratio of the length of the key to the diameter of the shaft (l/d) is
The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD is made of a brass with an allowable shearing stress of 5.8 ksi. Determine the largest torque T that can be applied at A if the allowable shearing stress is not to be exceeded in sleeve CD. The largest torque T that can be applied at A is ___ kip·in.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.