(B)-The winding sequence diagram show below for 4 pole d.c generator, 2-layer simplex progressive wave winding, the armature has 17 slots. Determine: (i) The back and front pitches measured in number of slots. b. yp N (ii) Number of conductors. (iii) Number of parallel branches in armature. 5 14 6 15 7 16 8 17 9 1 10 2 11 3 124 13 10 2 11 3 12 4 13 14 6 17 9

(B)-The winding sequence diagram show below for 4 pole d.c generator, 2-layer simplex progressive wave winding, the armature has 17 slots. Determine: (i) The back and front pitches measured in number of slots. b. yp N (ii) Number of conductors. (iii) Number of parallel branches in armature. 5 14 6 15 7 16 8 17 9 1 10 2 11 3 124 13 10 2 11 3 12 4 13 14 6 17 9

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An 8 pole DC shunt generator with wave winding has 4800 conductor with 20 turns and average per pole flux is 20 mwb and armature current and armature resistance is 20 A and 0.5 ohm respectively find? (i) Induced emf (ii) Terminal goltage
A short-shunt compound generator delivers a load current of 30 A at 220 V. It has armature, series and shunt field resistances of 0.05, 0.3 and 200 (ohm) respectively. Calculate the generated emf and the armature current. Allow 1.0 V per brush for contact drop.
22 The DC voltage is generated in the Armature winding of DC Generator. Select one: True False
Determine the coil and commutator pitches for a 72-slot 288-segment six-pole frog-leg armature winding.
A 2000V 3-phase 4-pole wye connected SM runs at 1800 rpm. The excitation is constant and gives an emf per phase of 1150V. The resistance is negligible compared to synchronous reactance of 3Ω/ . Determine the following when the armature current is 200A. a. Input power per phase b. Torque develop per phase
A 2 pole wave wound dc shunt generator runs at a speed of 750 rpm, has an armature and shunt field resistance of 0.4 and 580 respectively. The armature has 960 conductors and flux per pole is 0.115 Weber. If the lamp load connected has a resistance of 70 determine (i) Generated EMF, (ii) Total Resistance, (iii) Armature Current, (iv) Terminal Voltage.
Draw DC. Shunt generator which gives a full load output (30 K Watt) at the main voltage source of 200 voltage. In addition, gives the armature and shunt field resistors (0.05Ω and 50Ω), having 1000 watt iron and fractional losses. Calculate the Electro Magnetic field (EMF), Efficiency and Copper Loss.
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
A 12-kW, 250-V dc. shunt generator has armature and field resistances of 0.68 ohm and 120 ohm. respectively. Determine the total armature power developed in generator.
2) the armature windings of a 12-pole DC machine are composed of 72 coils with 10 windings, and the windings are 5the layered wave is yellowish. The Rotor speed is 1000 rpm and the flux value per pole is 25mWb.Resistance of Armature windings, commutation windings and compensation windings is 70mΩ, 10mΩ and5mω. (a) the number of current paths in the machine, (b) the total number of conductors in Armature windings, (c) armature coefficient (constant)
A 2000V 3-phase 4-pole wye connected SM runs at 1800 rpm. The excitation is constant and gives an emf per phase of 1150V. The resistance is negligible compared to the synchronous reactance of 3Ω/. Determine the following when the armature current is 200A. a. Input power per phase b. Torque develops per phase
To calculate the armature current of a synchronous generator, you do NOT need to know itsA. kilovolt-amperes.B. power factor.C. voltage.D. losses. Note: I have doubts if it is the letter A or the letter D, can you help me in this question, thanks.