16 A balanced, three-wire, Star-connected, three-phase load has a phase voltage of 240V, a line current of 4.2 A and unity powerfactor. Determine the total active power delivered to the load.Select one:O A. 99 WO B. 1746 WO C. 1008 WO D. 3024 W

Answered: Image /qna-images/answer/98bd23db-cb9f-4dae-bd5a-e90ac4395d28.jpg

Answered: balanced, three-wire, Star-connected,…

balanced, three-wire, Star-connected, three-phase load has a ctor. Determine the total active power delivered to the load. lect one: OA. 99 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Related questions

Q: Three Impedances each of (8 - j22)N are connected in mesh across a three-phase 400V ac supply.…

A: According the given equation, we can make the circuit diagram shown below

Q: A single phase wattmeter is used to determine the power taken by a three phase squirrel cage…

A: In this question, We need to determine the line current drawn by the motor. If Line to line voltage…

Q: One needs a 100 kVAr A-connected TCR for a three-phase distribution system of 2.4 kVu, and 60 Hz.…

Q: A 4MVA, 13.3kV, 60Hz, 3-phase, wye-connected alternator has an effective resistance of 5.2 ohm per…

Q: If the Vt = 230240°, determine the equivalent impedance submission bin "Solution" after the exam. In…

Q: Draw the block diagram of a load frequency control of a single area power system

A: Load-frequency control (LFC) : For large scale electric power systems with interconnected areas,…

Q: Q2/| answer true or false and correct the false ;if any. 1- The purpose of load test the single…

A: Electrical machines can be either generator , motors or transformers . They can be either Ac…

Q: In the circuit given in the figure, each switching element is triggered to remain in conduction at…

A: consider the given question;

Q: a-Calculate and draw the load current for the first two-period interval b-Calculate and draw the…

Q: During a specific time segment of the day, a remote producer has surplus power and a load center…

A: Electrical power system has three stages, generation, transmission and distribution. All the three…

Q: OR e) What is BILS? Explain their significance in power system studies.

A: BILS : BIL is stand for basic level insulation which is also known as lighting impulse voltage or…

Q: 1. For the given circuits, determine the RAB.

Q: A system has connected load of 120 kW, peak load of 100 kW, base load of 25 kW and average load of…

A: Given, A system has Connected load of 120 kW, Peak load (Max. demand) of 100 kW, Base load of 25 kW…

Q: (a) Discuss the high reliable distribution circuit with appropriate diagram.

Q: Considering the power transfer through an impedance between nodes 1 and 2, Z= R + jX, derive the…

A: Given impedance between node (1) and (2) is - Z=R+jXZ=R2+X2∠tan-1XRZ=Z∠θ

Q: (a) Based on the relationship between the line and phase value of currents and voltage, show that…

Q: Given a tee connected system with power factor of 80 percent and true power of 2,500 kW. Calculate…

A: In this question we need to find a reactive power.

Q: 37. 29 Discuss the causes and consequences of harmonic distortion Enlict the Power quality issues…

A: Given We need to elaborate the causes and consequences of harmonic distortion in power systems.…

Q: Q.5. (E3 10) State True or false a- The DC load flow study is an iterative process b- In a load…

A: Since we are allowed to solve only up to three sub parts in a question the solution below contains…

Q: Consider you have a network connected to a 100V,ms AC supply with an Ims of 10A and a power factor…

Q: c) A four-story office building has a required load of 60000volt amperes and single-phase 240volt…

A: A conductor is an device that allows the flow of a charge in one or more places. A standard…

Q: 8. A 3-phase, star connected alternator is rated 500 KVA, 1.1 KV. Its effective resistance/phase and…

Q: Homework Plot the blocking voltage of the SCR at a=0° for three-phase HWR. What is the value of PIV?

Q: if Pd exceeds Pg generation, what will be the effects on the frequency of the power systems

A: lf Pd exceeds Pg generation, The effects on the frequency of the power systems will be ?

Q: A 3Ø, 2000KW, 480V ∆-connected alternator is short-circuited and is operated at rated speed to…

A: Delta Connection: A delta connection is made up of three passive components that are either the same…

Q: Given a load factor of 0.48 and installed capacity of 35000kW, reserve over peak of 3000kW and hours…

A: Given, Load factor = 0.48 Installed capacity = 35000 kW Reserve capacity = 3000 kW Hour out of…

Q: A generating station has a maximum demand of 20MW,a load factor of 60%, a plant capacity factor of…

Q: If a 50 ohm quarter-wave impedance converter is used to match a 60 ohm transmission line to an…

Q: A 4MVA, 13.3kV, 60Hz, 3-phase, wye-connected alternator has an effective resistance of 5.2 ohm per…

Q: circuit feeding a single-phase load of 2.75 kW at 0.85 power factor and 240 V at an ambient…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Reactive Power Compensation Regulation, capacitive reactive power should not exceed what percent of…

A: Reactive Power Compensation Since the major load in power systems is an inductive load that…

Q: A 1500KVA, 8KV, three-phase wye-connected alternator has an effective resistance of 0.502 and a…

Q: Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50

Q: / Plot the blocking voltage of the SCR at ?=0o for three-phase HWR. What is the value of PIV?

Q: How to convert 22 mW of power into the units of dBm

A: In this case, 22 mW of power is to be converted into its equivalent power in dBm.

Q: e reactive power output of a mited by load angle True

A: In this question , we have to explain that which quantity limits reactive power output of an…

Q: 1988 FN.Q4-Each phase of a star-connected load comprises a resistance of 56 2 and a 155 mH…

A: As per the guidelines of Bartleby we supposed to answer first three subparts of the question for…

Q: Draw the circuit diagram of power system layout with three phase CT and three phase PT.

A: Electrical Transformers can be used as Measuring devices when used in specific configuration. These…

Q: Given that Vin 110230° V find Vanand Ven assuming a positive (abc) sequence. %3D

Q: If value of voltage Vs is 20kv and VR is 15 kv with load angle of 20 degrees. Value of line…

A: Given values are - VS=20kVVR=15kVδ=20oX=5Ohm

Q: non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a…

Q: 24: A 3 phase half-waye controlled Vectifier is operated from '3-phase, line to line voltage 230U,…

Q: A 3Ø, 2000KW, 480V A-connected alternator is short-circuited and is operated at rated speed to…

A: Delta Connection: A delta connection is made up of three passive components that are either the same…

Q: O O A.C. distribution calculationg differ from of d.c. distribation power factor, vectarially…

A: For DC distribution frequency is 0, also there is no phase so addition is algebrically.

Q: Q4/ What is the three phase emf generation and show their two main advantages with type of…

A: Three phase emf generation- A three-phase device has three equivalent voltages or emf of the same…

Q: Problem 9: Determine the complex power absorbed by each passive component in the circuit shown…

Q: Explain the advantages of power factor correction for the load (consumer) and the grid.

A: If the power factor is low, the percentage of the measured KVA will be significantly greater than…

Q: Describe real and reactive power regulation

A: The power which which is consumed by the loads connected to the system is called real power The real…

Q: ) For the circuit shown, determine a) Vo cVz. Power at (3ua) & (2011) Зил Shs 10MA 20ks ns-[a)15V,…

A: In this question we will find voltage drop and power across 3k ohm and 20 k ohm resistor using KVL…

Q: ) A single-phase full-wave AC voltage controller consists of two SCRs connected in invers-parallel.…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

A balanced, three-wire, Star-connected, three-phase load has a phase voltage of 240V, a line current of 4.2 A and unity power
factor. Determine the total active power delivered to the load.
Select one:
O A. 99 W
O B. 1746 W
O C. 1008 W
O D. 3024 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A balanced star connected load of (8+j 6)Ω per phase in connected to a balanced 3-phase 400 V supply Find the line current, power factor, active power and reactive power.
A 415 V, 50 Hz, 3-phase supply is connected to a star-connected balanced load.Each phase of the load consists of a resistance of 25  and inductance 100mH,connected in series. Calculate (a) phase voltage, (b) the line current drawn from thesupply, and (c) the power dissipated.
Problem : The power supply in the diagram below provides 40 kW at a power factor of 0.9 leading. The active power loss and reactive power loss on the transmission line are 1.6 kW and 2.1 kvar, respectively. Calculate the load voltage, as well as the active and reactive power at the load. Answer given : VL=416.83∠(-162°) V, PL=38.4 kW, QL=17.27 kvar.
A star-connected three phase power pack is connected to balanced star-connectedload of 2 + j3 Ω. The line current is 2∠0⁰ A. Assuming negligible impedance onthe cable, calculate:a) the phase and line voltages from the source. b) the real and reactive powers of the circuit.
8) A balanced star-connected load of (8 + j6) Ω per phase is connected to a balanced 3-phase 400-V supply. Find the line current, power factor, power and total volt-amperes
A 3-, 400-V symmetrical supply feeds a star-connected load consisting of non-reactive resistors of 3, 4 and 5 connected to the R. Y and 8 lines respectively. The phase sequence is RYB. Calculate (1) the load star point potential (i) current in each resistor and power dissipated in each resistor.
According to the relevant legislation, the reactive energy tariff is not applied to household subscribers with connection power in kW and below, lighting subscribers, single-phase subscribers and producers that provide energy (generation) to the system? a) 5. b) 12 c) 9. d) 50
A balanced delta connected load, consisting of there coils, draws 10-√3 A at 0.5 power factor from 100 V, 3 phase supply. If the coils are re-connected in star across the same supply, find the line current and the total power consume.
When drawing three-phase inductive 250 kW from the 440 V transmission line, the power coefficient is 0.707. When a three-phase parallel 60 kVAR capacitor group is connected to this load, find the current drawn from the line and the power coefficient?
A series circuit composed of a resistance of 24 ohms, an inductance of 0.09 henry and a capacitance of 8 microfarad, is connected to a 120-volt 50-Hz supply. Calculate (a) the line current, (b) impedance of the circuit, (c) voltage drop, (d) total reactive power, (e) power factor.
A factory has the following load with power factor of 0.9 lagging in each phase. Red phase 40 A, yellow phase 50 A and blue phase 60 A. If the supply is 400 V, three phase, four-wire, calculate:(a) the current in the neutral(b) the total active power.(c ) Draw a phasor diagram for phase and line quantities. Assume that, relative to the current in the red phase, the current in the yellow phase lags by 120° and that in the blue phase leads by 120°.5.
Three Impedances each of (11 – j20)Ω are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from the supply. Also, draw the Phasor diagram for the mesh connection and mark the Line current, phase current line voltage, and phase angle between phase current and phase voltage. phase current (Ip) = Line current = real power= reactive power=