Below picture shows the composite wall block diagram. Calculate the thermal resistance of each blocks of A, B and C. Draw the thermal circuit diagram for the below composite blocks and hence find the heat flow rate at steady state in the given direction. Heat capacities of materials A, B and C are 120 W/ m C, 40 W/ m C and 20 W/ m C respectively.

Below picture shows the composite wall block diagram. Calculate the thermal resistance of each blocks of A, B and C. Draw the thermal circuit diagram for the below composite blocks and hence find the heat flow rate at steady state in the given direction. Heat capacities of materials A, B and C are 120 W/ m C, 40 W/ m C and 20 W/ m C respectively.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.35P

See similar textbooks

Similar questions

1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
The front door of an oven is made up of walls made up of materials A, B and C, juxtaposed. The walls that make up the door have thermal conductivities, kA= 20 W/(m.K), kB= 0.027 W/(m.K) and kC= 50 W/(m.K) and known thicknesses LA=0.30 m and LC=0.15 m. At steady state operation, measurements indicate that the air temperatures inside the oven and its inner walls are equal to 600 oC (the temperature of the inner surface of the door is not known). The convective coefficient of air (inside and outside the oven) is 25 W/(m2.K) and the radiation coefficient is hr=25 W/m2K. outside the air is at 25oC. Based on this information:(a) schematic the thermal circuit for the system;(b) estimate the minimum thickness of wall B to ensure that thetemperature of the outer surface of the door (exposed to ambient air)is ≤40oC in order to ensure the safety of operators;(c) estimate the temperature of the surface of the oven's inner wall Answer: (b) 40 mm; (c) 592.5oC
1a.A copper slab ( k = 372 W/m .K ) is 3mm thick . it is protected from the corrosion on each side by a 2 mm thick layer of stainless steel ( k = 17 W/m .K ) . The temperature is 40oC on one side of this composite wall and 100oC on the other. Find the temperature distribution in the copper slab and the heat conducted through the wall. Given: ksteel = 17 W/m .K kcopper = 372 W/m .K Steel Copper Steel T1 = 40oC T2 T3 T4 = 10oC q…
4) In an experiment to find the thermal conductivity, a metallic rod of diameter 25 mm is placed in a furnace such that its one half is inserted into the furnace and other half is projected out in a room at 300 K. Once the steady state reached, the temperatures measured between two points 76 mm apart were 399 K and 364 K, respectively. Taking a convection coefficient of 22.7 W/m 2 – K, find the thermal conductivity of the metal.
The wall of an industrial kiln is built in refractory brick with 0.18 m thick, whose thermal conductivity is 1.7 W / (m.K). In steady state, the oven has a temperature of 1400 K on the inner wall and 1000 K on the outer wall. What rate of heat loss through the wall that is 1.6 m² in area? Draw a wall with a graph of temperature variation in its thickness.
In a glass plant in Cavite, a furnace has fire-brick walls made up of the following two materials in series : Non-corrosive brick as inner layer (material 1) Clay brick as outer layer (material 2) Thickness 4.5 inches 8 inches Thermal conductivity k1 k2 The temperature inside the furnace (inside wall surface of the non-corrosive brick) is found to be 1105 oF while the outside temperature (outside wall surface of clay brick) is 365 oF. This is not the desired temperature inside the furnace so engineers thought of lagging the furnace walls with another material to reduce heat loss. The additional lagging material consists of magnesia layer which is 2 inches thick and has a thermal conductivity of 0.04 Btu /h.ft.oF. During a test run on the furnace with the magnesia lagging material now, new temperature readings were recorded : Point of measurement Temperature reading Inside furnace (inside wall surface of non-corrosive brick 1355 oF Interface between…
A wall consists of a layer of wood and a layer of cork insulation of the same thickness. The temperature inside is 34.0°C, and the temperature outside is 0.0°C. The thermal conductivity of wood is 0.130 W/(m·K) and the thermal conductivity of cork is 0.0460 W/(m·K). A) What is the temperature at the interface between the wood and the cork if the cork is on the inside and the wood on the outside? in C B) What is the temperature at the interface if the wood is on the inside and the cork is on the outside? in C C) It doesn’t matter whether the cork is placed on the inside or the outside of the wooden wall because the temperature at the interface differs for the two cases.the temperature at the interface differs for the two cases. the temperature at the interface is the same for the two cases.the temperature at the interface is the same for the two cases. the total thermal resistance is the same for the two cases.the total thermal resistance is the same for the two cases.…
Two parts and label (A) & (B) Solve carefully! Question : The roof of a car in a parking lot absorbs a solar radiant flux of 600 W/m2, while the underside is perfectly insulated. The convection coefficient between the roof and the ambient air is 15 W/m2.K and the roof’s surface emissivity is 0.5. If the ambient air temperature is 25C, answer the following questions: PART (A) Neglecting radiation heat transfer, find the temperature of the roof under steady state conditions. Part ( B) Neglecting convective heat transfer, find the steady state temperature of the roof [Tsur =0]?
10 km of steel railroad track are placed when the temperature is 20 C. The linear coefficient of thermal expansion for the rails is 11 x 10^6 1/ C. The track is free to slide forward. How far apart will the end of the track be when the temperature reaches 50 C
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.