Box your final answers. Use appropriate symbols and round off your answers into two (2) decimal points only. 1. A uniform beam is 6.0 m long and has a mass of 60 kg. The beam is supported in a horizontal position by a hinge and a cable, with angle 0 = 130°. a) What is the tension on the cable? b) What are the magnitude of the vertical and horizontal forces acting on the hinge? c) What is the magnitude and direction of the torque exerted by the tension on the cable? 130°

Box your final answers. Use appropriate symbols and round off your answers into two (2) decimal points only. 1. A uniform beam is 6.0 m long and has a mass of 60 kg. The beam is supported in a horizontal position by a hinge and a cable, with angle 0 = 130°. a) What is the tension on the cable? b) What are the magnitude of the vertical and horizontal forces acting on the hinge? c) What is the magnitude and direction of the torque exerted by the tension on the cable? 130°

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 100A

See similar textbooks

Similar questions

The answers are provided; please explain the purpose of each equation and why they were used Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 28 N and the first force is acting on the end of the bar at an angle of 43° What is the torque in newton-meters, due to F1 on this bar relative to the left end? Ans. = 78.87 Nm Equation used: τ1 = rFsinθ What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. Ans. = 77 Nm Equation used: τ2 = F2 x (L / 2) What is the magnitude of the force F3, in newtons, if the force is a distance 0.85 m from the left end and the bar is not rotating? Ans. = 183.38 N Equation used: F = (τ1 + τ2) / d
What does the scale (at the center of the rod) read? What is the force the supporting rod applied to the massless rod? Please label each force on the diagram and indicate the pivot point you chose when calculate the torque. 1000N
Suppose the hand in (Figure 1) holds an 8.9 kg mass. The total mass of the arm is 3.3 kg. What force, FM, is required of the deltoid muscle, assuming the mass is 48 cm from the shoulder joint? Express your answer to two significant figures and include the appropriate units.
hello, can you pls help me solve this as for my understanding on our topic Torque.. I can't inderstand it. pls draw a diagram and label it, use 3 decimal places and correct units so it will be easier for me to understand. Thank you a) a force acts on an A-truss (as shown on the diagram attached). Determine the value of the individual torques and the total torque about point A. our formula in solving Torque is (t = F x l ; where F is the torsional force applied, l is the level arm or the distance between the fulcrum) pls help me understand this. thank you
In the wheelbarrow of Figure shown, the load has a perpendicular lever arm of 7.50 cm, while the hands have a perpendicular lever arm of 1.02 m. What upward force must you exert to support the wheelbarrow and its load if their combined mass is 45.0 kg?
Luis uses a 20-cm-long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30° above the horizontal, and Luis pulls straight down on the end with a force of 100 N. How much torque does Luis exert on the nut?
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
The large quadriceps muscle in the upper leg terminates at its lower end in a tendon attached to the upper end of the tibia (see Figure a). The forces on the lower leg when the leg is extended are modeled as in Figure b, where T is the force of tension in the tendon, w is the force of gravity acting on the lower leg, and F is the force of gravity acting on the foot. Find T when the tendon is at an angle of 25.0° with the tibia, assuming that w = 29.0 N, F = 12.3 N, and the leg is extended at an angle ? of 40.0° with the vertical. Assume that the center of gravity of the lower leg is at its center and that the tendon attaches to the lower leg at a point one-fifth of the way down the leg. (Give the magnitude.)
If you hold your arm outstretched with your palm upward, the force to keep your arm from falling comes from your deltoid muscle. Assume that the arm with hand has mass 4.25 kg and the distances and angles shown. What force must the deltoid muscle provide to keep the arm in this position, in Newtons? Use g = 10.0 m/s2. the answer is 367, please explain how?
PLEASE PUT SOLUTION (WHY) // WHY THE REASON OF THAT ANSWER (?) 1. What should be done to increase the generated torque on a bar, with one end fixed to a point, without increasing the applied force? A. Make the moment arm shorter. B. Increase the weight of the moment arm. C. Move the axis of rotation closer to the point where force is applied. D. Increase the length of the moment arm. 2. How will the generated torque change if you move the axis of rotation from the middle of a bar to its left end, given that the applied force is applied at its right end? A. Torque will be doubled. B. Torque will increase 1.5 times the original. C. Torque will remain the same. D. Torque will be halved.
How many forces provide the counterclockwise torque in the first part of the experiment? P.s. I had this question answered but I was confused on what the actually answer is. Is there only one force or three forces providing the couterclockwise torque? Please clarify more.
The 3.000-m-long, 100.0 kg rigid beam of the figure given below is supported at each end. An 80.00 kg student stands 2.000 m from support 1. (a) Show the FBD of the beam with complete and correct labels of all forces and moment arms.(b) How much upward force does each support exert on the beam?