Briefly describe what is meant by a right handed system of coordinate

Q: For a pump designation 1-x3-10 provided by the manufacture, find out the appropriate options for…

A:

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: Give two reasons for using standard letter designations

A: There are standard abbreviations called as letter designations used for showing various welding…

Q: Define the term layout and briefly explain the purpose for layout.

A: Given Data : Layout

Q: 3- The front and top views of an object are shown below. Freehand sketch the partial auxiliary view…

A: Given front and top view

Q: What are all the distances between datum target points, B1 and B2 ? Y = Z =

A: Solution:

Q: 3. IY 2.

A: there will be 15 ICs so, locate all IC will little bit lengthy and cumbersome process.follow step by…

Q: at direction should you paddle te

A: 21.80 Degree ( from downstream)

Q: provide Orthographic view

A: Question fig.

Q: What does the schematic symbol below representing?

A:

Q: ley is a uniform disk (Idisk= the cord unwinds, the acceler

A: given:mass=1.1kgmass of pulley M=3kgR=20cm

Q: QUESTION 4 Moving by 1 inch in the X-direction, from an X-Y coordinate location of (3.5, 2) to (4.5,…

A: Types of positioning movement - (i) Absolute positioning movement (ii) Incremental positioning…

Q: The acronym PASS' is used to explain the method of using fire extinguishers. In this, 'A' stands for…

A: The acronym PASS, which stands for Pull, Aim, Squeeze, and Sweep.

Q: Which of the twelve geometric controls is the most common? O Angularity O Position O Flatness O…

A: A feature control frame is used in GD&T to show the condition and tolerance provided in the…

Q: term gB(T - To) represents

A: Given: 2-D momentum equation for natural convection over a surface immersed in a quiescent fluid at…

Q: Define translating coordinate system.

A: Coordinate systems are those systems which are used to specify the location of any point in space.…

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Sketch the orthographic view

A: Solution: The front, top and side views are shown below:

Q: Find dof of the robots shown the below Figures: Universal Joint

A:

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: Draw the top and front view of the figure 2 using AutoCad

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Sketch the Orthographic and  auxiliary view

A:

Q: Define the speed of point C.

A: The given system is rack and pinion arrangement. The tangential velocity at A is given as 2 ft/s and…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: Basically a NC machine runs on a program fed to it through Punched tapes Select one: True False

A:

Q: the angular velocity

A:

Q: he velocity of. he velocity of CI CI

A: given:block B acceleration =3m/s2blo0ck B velocity =2m/s

Q: Evaluate:∫ds

A: From question   ∫ds = S + c Where c is Intregated constant.

Q: mode shapes

A: mx¨+kx=F for free vibration F=0 mx¨+kx=0 mass matrix m=m000m000m=m100010001 stiffness matrix…

Q: a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is…

A: Knocking is the phenomena commonly occurring in a CI engine. You may know that in a CI engine the…

Q: The other degree of rotation from the start point that will result in Erika being the same distance…

A:

Q: What is translating coordinate system?

A: Let suppose a 2D coordinate system with origin O. position vector in this coordinate system is…

Q: The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the…

A: BREAK Command is a tool in AutoCAD software which is used for removing part of an object, open or…

Q: Draw an isometric view of the following Dovetail Slide.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Draw the phasor c

A: Phasor Diagram of transformer. Note: There are two question posted by the student both are different…

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: Calculate two blocks acceleration

A: For solution refer below images.

Q: 1. What is your mech diameter of 3

A: given:l=35cmr=3/2cm

Q: i) Kinematic Diagram Abtor

A: To determine the degree of freedom of the given kinematic diagram.

Q: where is starting point

A:

Q: As mentioned in the below given DCV, extend stroke respectively. and Lare the positions are used for…

A:

Q: Which command is not modal?

A: All are modal for G code.

Q: d. 1. What are the four types of moves and describe how they move between waypoints. a. b. C.

A: Given Robotic motion To find Types of motion

Q: What is the shortcut key for "Find and ?Replace" dialog box + Ctrl + Shift + FO Ctrl + RO Ctrl + FO…

A: Correct answer: Ctrl + H

Q: Draw (hand drawing) three views of the following components, in third angle projection (including…

A: Draw the all three diagrams of figure (1).

Q: employ a pointer moving over a fixed scale.

A: The correct answer for this question is  Indicator employs a pointer moving over fixed scale

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: How to draw front view and top view of the following componen

A: Orthographic Projection is a technique for drawing a three-dimensional object from various angles.…

Q: BLOCK DIAGRAM draw the schematic diagram of these components using standard symbols. FLOW CONTROL…

A: The symbolic representation of the block diagram is known as the schematic diagram. Schematics…

Q: 2. Draw the hole in the top and front views: .625 through hole, 90 degree countersink to 1.250 dia.

A: ◆ The purpose of providing countersink is to accommodate the head of the bolt within the workpiece.…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.