By comparing the performance of DC -DC chopper with controlled rectifier circuit, which one of the following statement is correct? O a. Switching frequency is not responsible for output ripples in chopper circuit O b. Efficiency is poor in chopper circuit O. Regenerative braking process is very slow in chopper circuit O d. small filters are required in chopper circuit

By comparing the performance of DC -DC chopper with controlled rectifier circuit, which one of the following statement is correct? O a. Switching frequency is not responsible for output ripples in chopper circuit O b. Efficiency is poor in chopper circuit O. Regenerative braking process is very slow in chopper circuit O d. small filters are required in chopper circuit

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? a. Switching frequency is not responsible for output ripples b. small filters are required c. Regenerative braking process is very slow d. Efficiency is poor in chopper circuit
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
a half-wave rectifier circuit in the figure below has a transformer inserted between the source and the remainder of the circuit. The source is 240 Vrms at 60 Hz, and the load resistor is 20 ohm. (a) Determine the required transformer turns ratio (Ns/Np) so that the average load current is 12 A. (b) Determine the average current in the primary winding of the transformer.
Draw the circuits, voltage and current plot of: a. A halfwave rectifier with capacitor filter b. A fullwave rectifier with capacitor filter c. A Full wave rectifier with center tap transformer and derive the equations of all of them
Suppose line voltage may be as low as 105 Vrms or as high as 125 Vrms in a half-wave rectifier. With a 5;1 step-down transformer, the minimum peak load voltage is closest to___
What is mean by phase angle control method?. Differentiate Natural and forced commutation method. Is it possible to construct rectifier circuits by MOSFET? Justify. ( short anser only plases )
Suppose you are an electronic circuit designer. How you can use the center-taped step down transformer in bridge rectifier circuit?
4- What is the effect of adding capacitor in parallel to the load at the rectifier output? Note: Please do not handwritten.
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, The transformer is specified to have a 12 V rms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than1.5percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b)What is the PIV rating for the diode? (c)What is the rms value of the transformer voltage needed for the rectiﬁer?(d) What is the value of the peak repetitive diode current in the diode? (e) What is the surge current at t =0+?
Both ripple factor and harmonic factor should be unity for ideal controlled rectifier. Select one: True False