Answered: Calculate the average power transferred…

Engineering

Electrical Engineering

Calculate the average power transferred by the source in the circuit given below

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter16: Inductance In Ac Circuits

Section: Chapter Questions

Problem 1PP: Inductive Circuits Fill in all the missing values. Refer to the following formulas:...

See similar textbooks

Related questions

Q: For the circuit shown below, determine the real, reactive and apparent power for each element…

A: Write KVL equation for the circuit given and solve for current I; 2402∠60°-I5+8j-2802∠30°=0…

Q: 2. Determine the average power P delivered by each of the three sources. 6 cos 377t A 155 cos 377t V…

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: In this question, We need to determine the power supplied by the power company? If power factor…

Q: determine the value of load Z for maximum power transfer

A: Voltage division method- When elements are connected in series then voltage drop across any single…

Q: Find the complex power supplied by the source and the power factor of the source for the network…

A: From given load parameters calculate line current I. Sending end voltage = receiving end voltage +…

Q: Consider the AC voltage shown below. (()v V ponif the frequency of the voltage in units of Hz. DO…

A: The given AC voltage is v1t=2cos50πt+π6 Volts. We need to determine the frequency of the voltage in…

Q: Consider the problem of maximizing the average power absorbed by the load impedance Zjoad- j1 Ω 12Ω…

A: Given circuit is –

Q: Complete the blank The load of 660 kVA with 0.62 power factor lagging, then the kW rating of the…

A: Load rating 409.2 KW

Q: A 2 MW generation station has a daily average load of 500O kw with plant use factor of 0.8. The…

A: The plant use factor is defined as: Plant use factor =Actual energy generated (kWh)(Plant…

Q: The total installed electric generating capacity of Pakistan is about 38719 MW. Find the installed…

A: The total installed capacity of the public sector power plants in the country was 19621 MW while the…

Q: For the following circuit, determine the average power supplied by the source to the net.

Q: For the following circuit, determine the average power supplied by the source to the network.

Q: -2. A. A lighting load of 2000 kW and a mo pplied by two alternators running in parallel E. lagging.…

Q: Determine the power factor of the entire circuit below as seen by the source. Calculate the average…

A: In this question we need to find a input power factor and average power delivered by source.

Q: An equipment that draws 9.4 kW at 0.83 power factor lag. How much reactive power in kVAr is…

A: Reactive power = active power ×tan(power factor angle). Power factor angle = arc cos(power factor).…

Q: For the given network diagram find the complex power and power factor supplied by the source. 0.1Ω…

Q: The value of power at any instant is given by the product of the voltage and current at that…

Q: Find the average power absorbed by the load with Z = 21 + j24 ohms

Q: IDm ALOO 100s2 Ikse

A: In the given circuit the three impedances 1000ohm, j100ohm, -j4ohm are in parallel. We will first…

Q: 15. A residential AC power line voltage is 230 V. What are the average and peak-to-peak voltages? a.…

A: In this question we will find average voltage and peak to peak value for given wave with line…

Q: generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 k . The station…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Q10. If the impedance of a circuit = 20 – j10 1. if a voltage source is connected across this…

A: Given: Impedance Z=20-j10Ω Voltage source is connected across impedance.

Q: The values of the elements for the given circuit are given below. The maximum average power that can…

A: The given circuit is shown below. We need to calculate the maximum power transferred to the load…

Q: Two alternators A and B delivers 100 and 150 A, respectively to a load. If these currents are out of…

A: Use pythagoras theorem to find current current drawn load.

Q: Calculate the average power þ Power Factor ww 8N N -jun 5010° deliverd by the 62 ww 11 fir source.

Q: Given the network in the figure below, determine the magnitude of the input voltage Vs. 0.3 0 jo.1 N…

A: Given network,

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: This question belongs to circuit theory . It is based on the concept of power factor in the circuit…

Q: Find the total apparent power falling on the loads and the power factor of the system.

Q: A generator is supplying a load of 500 kW at a power factor of 0.8 lagging. If the power factor is…

Q: Find the complex power supplied by the source and the power factor of the source for the network…

A: The solution can be achieved as follows.

Q: 2. Determine the average power absorbed by cach resistor, the total average power absorbed and the…

A: Given figure as- I1=12∠45°4I1=3∠45°I2=12∠45°2-j1Ω=12∠45°2.236∠-26.56°I2=5.366∠71.56° A

Q: For the circuit shown, find the average/real power (in W) supplied by the source.

Q: Which of the following equipment should be installed by the consumers having low power factor

A: Equipment used by consumers to improve the power factor is :-

Q: For the circuit shown beside, find The average power delivered to the circuit

Q: Determine the average load voltage in the circuit and the power delivered to the load if C= 47µF

Q: the currents 11

Q: Calculate the average power delivered by the source. 6Ω ww 30/0° V rms (+ -j2 2 4Ω Note: You are…

A: Given circuit,

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power rating, P1 = 300 kW Power factor, cosϕ1 = 0.6 lagging At power factor, cosϕ2=1…

Q: (d) The impedance in ohm of each coil. (Polar form) (e) The value of the resistance in ohm of each…

Q: a series circuit contains a resistance of 55.1 ohms and the voltage across through it has equation…

Q: 80 -j2 n 4<0° A -j3 0 50 j20 10<30° V

Q: A power plant is characterized by an annual load factor of 60%. Assuming that the annual peak load…

A: Given load factor=60% Annual peak load=20000 kW

Q: appropriate formula that articulate the instantaneous power and the average power respectively.

A: Here it is asked to find the difference between average power and instanteneous power. Here…

Q: The load of 860 kVA with 0.69 power factor lagging, then the kW rating of the load is

Q: Exercise Problem 8.22 Determine ix(t) and average power delivered by the source.

A: N1N2=14i1N1=i2N2N1N2.i1=i2i2=N1N2 i1i2=14 i1jωL1=j13=j3Apply KVL--7∠0°+i14+i3j3+5i3=0…

Q: A series circuit contains a resistance of 55.1 ohms and the voltage across through it has equation…

A: Resistance R=55.1ΩVoltage equ e=23 cos ( 314t−50∘) V Current equ can be calculated as I=eR=23 cos (…

Q: The average power lost in the transmission line (single phase) is equal to the power produced by the…

A: The average power lost in the transmission line (single phase) is equal to the power produced by the…

Question

Calculate the average power transferred by the source in the circuit given below

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the equation of a 25 cycle current wave having rms value of 45 amp? a. 31.8198 sin 157.08 t b. 45 sin 157.08 t c. 63.6393 sin 157.08 t d. 90 sin 157.08 t
R= 10 Ω , L= 10 mH, C=5000 nF, V(DC) =50 Volt, F= 100 hz Write the voltage function vC (t). and calculate for vC(t=0.01)
given: V1= 13.1V V2= 17V R1= 3.5 kilo-ohms R2= 6.4 kilo-ohms Solve the magnitude of the power (inmW) dissipated atR1
A 100 ohm (0 oC) RTD has a temperature coefficient of α= 0.00385 Ω/ Ω/ oC. What is the resistance of the RTD at temperature 550 oC? 211.11 213.54 411.34 311.75 102.11
The answers were already given. a. 98.9949 Vb. 197.9899 Vc. 70 Vd. 100 mse. 10 Hzf. 20π rad/secg. 54.9124°h. v(t) = 98.9949sin(20πt - 54.9124°)i. 29.0880 Vj. 108.8253°k. 66.8639 ms
Many have witnessed the use of an electrical megaphone for amplification of speech to a crowd. A model of a microphone and speaker and the circuit model are shown. Find v(t) for vs = 10sin(100t)u(t), which could represent a person whistling or singing a pure tone. Answer: (1.55 e−0.6t−1.55 cos100t + 0.279 sin100t)V
solve the equation for I(t), Resistance (ohm): 5.7Capacitance (millifarad): 20.76Inductance (millihenry): 1.2Voltage (volts): 220Frequency (Hz): 50
The voltage v = 201 sin(100t+50°) V is connected acroos a 110-µF capacitor. Determine the current (RMS) in polar form. Write the magnitude only in four decimal places.
Derive the relationship for maximum power Eb = v/2
need asap 34. The voltage across a 10 microfarad capacitor is v(t) = 50 sin (2000t) volts. What is the current in ampere flowing through it at time, t= 0,5 seconds? Note: the unit of thequantity 2000 is radians/second.
The voltage v = 119 sin(100t+50°) V is connected acroos a 8-H inductor. Determine the current in polar form. Write the magnitude only in four decimal places.
What is the equation of the current in B in the function of sin given that Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total linecurrent is 23.4 amp. (rms).