Calculate the heat transfer per hour through a solid brick wall 6 m long, 3 m high, and 240 mm thick, when the change in temperature is equal to 15 C, the coefficient of thermal conductivity of the brick being 0.6 W/m-K

Calculate the heat transfer per hour through a solid brick wall 6 m long, 3 m high, and 240 mm thick, when the change in temperature is equal to 15 C, the coefficient of thermal conductivity of the brick being 0.6 W/m-K

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.41P

See similar textbooks

Related questions

Q: 100 Design a manufacturing process to produce a 0.1-inch thick copper plate having at least 300 MPa…

A: Given : To find : Design manufacturing process

Q: A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forces P, = 12 kN, P, = 8 kN,…

A: Given data P1 = 12 kNP2 = 8 kNP3 = 6 kNa = 1.5 mb = 0.6 mc = 0.9 mE= 210 GPa

Q: A channel is formed by having two vertical brick walls with a semi circular culvert at the bottom.…

A: As per the guideline, I can solve only first question. For second question, repost in a separate…

Q: A cylindrical steel pressure vessel 60 cm in diameter with a wall thickness of 30 mun, is subjected…

A: INTRODUCTION : Pressure vessels are pressurized gas storage containers whose function is to contain…

Q: Q1/"Current trend in Energy Supply and use are patently unsustainable-economically, environmentally…

A: Main idea of the article is.. c)the low carbon technologies have a crucial role to change the energy…

Q: Neglecting air resistance, determine to what height a vertical jet of water could rise if projected…

Q: iv. Calculate the force FBC in the member BC between node joints B and C. V. Calculate the force FAE…

Q: C. D z into an aquifer. Assuming that chloride is a completely conservative tracer, that /day and Dy…

Q: Q3: In iron whose base plaet is mad aluminum alloy is turn on : The time for the plate temperature…

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a.…

A: Given Width, B = 1000 m Depth, Y = 2 m Conversion…

Q: where are you finding v=0.0159939 m3/kg ? , when I look for the specific volume for saturate steam…

Q: Increasing the frequency of the supply will: O Decrease the rotor speed at a certain load torque.…

A: INTRODUCTION : Induction motors are used on circuits with different voltages or frequencies than…

Q: 9-5 A vertical plate 30 cm wide and 1.2 m high is maintained at 80°C and exposed to saturated steam…

Q: calculate the leakage mass flow rate per unit area from the first ring pack plenum to the cylinder…

A: Given Temperature, T = 450 K Coefficient of discharge, C = 0.75…

Q: The solution to y" + 9y = 5 cos wt will exhibit %3D (a) resonance when w= (b) beats when w= (There…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Given the following state of stress where ox = 50 MPa, 0y = 0 MPa, txy = %3D -25 MPa, (i) draw…

Q: In orthogonal cutting, the depth of cut is 0.5 mm at a cutting speed of 2 m/s. If the chip thickness…

Q: QUESTION 14 A metal matrix composite consists of continuous silicon carbide fibres of radius 25…

A: Given; The radius of silicon carbide fibers, r = 25µm The volume fraction, xf = 0.35 The weibull…

Q: Study the double slider crank mechanism in figure A: (a) Using Aronhold Kennedy Theory formula,…

Q: The internal pressure of a 400 mm inside diameter cylindrical tank is 10 MPa and the wall thickness…

Q: A 37.3 kW [50 HP] gasoline tractor is used to operate a pull-type sprayer. The tractor’s list price…

A: Given DataTractor listed price=$6500Total hours =400 hours/yearSprayer list price=$15000Tractor…

Q: A supercooled water droplet turning into ice is called ____________. a. c. deposition b. e.…

A: Concept: 1) Water droplets generally in liquid state. 2) While supercooling, the temperature of…

Q: Q3/ 0.34 m' of a perfect gas at constant pressure of 2.8 bar is heated from 100°C to 300°C and it is…

Q: Determine the greatest allowable acceleration of the system.

Q: 1. A Francis turbine operates at its maximum efficiency point at no 0.94, %3D corresponding to a…

Q: For the system shown in figure. find the power that the turbine can extract. The discharge through…

Q: : In some application, Methane is mixed with air as ratio 1/13 by mass, then the mixture entering to…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 255 lb-ft and TD= 95 lb-ft,…

Q: One Kmol of C8H18 is burned with 100% air containing 25 Kmol of O2. Determine the air- fuel ratio…

Q: 14.35 PQ< What is the difference between a system curve and a pump curve. Explain.

Q: Initially, a rigid tank contains 500L of water at 300°C. By volume, the tank contains60% liquid and…

Q: simply supported beam of length 7m has a concentrated couple Mo of 10kn-m applied at one end.…

Q: Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For…

A: I have used steam table to fetch the properties of steam and also while doing interpolation atmost…

Q: For the compressor linkage in the belwo figure, at the instant shown, the crank is rotating…

Q: 1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height =…

A: Given Datad=75mmh=50mmt=3mmRd=4mmσt=400MPa

Q: 1. Status comes under which of the following types of barriers? A Semantic barrier B. Organisational…

Q: 6. An air-conditioning system operates at a total pressure of 95 kPa and consists of a heating…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: what is meant by each of the following? 1. Refrigerant 2. GWP factor 3. TEWI 4. Brines 5. eutectic…

A: As per the Bartleby answering guidelines we are supposed to answer first Question only. please…

Q: Figure 1 of 1 |2P A -2 ft- -2 ft- d 2 in.

A: find the maximum magnitude of load P.

Q: QUESTION 14 A metal matrix composite consists of continuous silicon carbide fibres of radius 25…

A: 14. Given: The volume fraction of silicon carbide fibre, xf = 0.35 The radius of silicon carbide…

Q: Figure P3-41 3-41 For the insulated corner section shown in Figure P3-41, derive an expression for…

Q: A two-stage, double-acting compressor is to deliver 90 lb/min of air from 14.3 psia and 90 ̊F to a…

A: Given data, Mass flow rate of the air, m˙a=90 lb/min = 1.5 lb/s Pressure at state 1, P1 = 14.3 psia…

Q: what is the CW you are using in the quations , and where do you find it ?.

Q: Prove that there is an increase in efficiency between a Simple Rankine Cycle and a Reheat Rankine…

A: Given data Reheat Rankine cycle with the following conditions: Steam entry at High pressure turbine…

Q: 3-Use implicit differentiation to find the slope of the tangent line to the curve at the specified…

Q: Process of forming metal powder by directing molten metal through an orifice after which it is break…

A: This question is based on the concept of manufacturing science.

Q: The post is constructed from concrete and six A-36 steel reinforcing rods. If it is subjected to an…

Q: Explain the physical interpretation of the four Maxwell relation.

Q: Using the float method in determining the velocity of water through a channel, the float velocity in…

A: Option b is correct.

Q: Appreciate if you could show clearly solution for me to understand ??

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500C, while that of the ambient air in the room is 20C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10 W/m2K.
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.