Calculate the moment of resistance of a R.C. beam of rectangular section 250 mm wide and 500 mm deep, if it is reinforced with 6 number of 20 mm bars on tension side and 5 number of 20 mm bars on compression side. Assume steel of grade Fe 250 and concrete of grade M20. Effective cover provided is 40 mm on both sides.

Calculate the moment of resistance of a R.C. beam of rectangular section 250 mm wide and 500 mm deep, if it is reinforced with 6 number of 20 mm bars on tension side and 5 number of 20 mm bars on compression side. Assume steel of grade Fe 250 and concrete of grade M20. Effective cover provided is 40 mm on both sides.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Design a rectangular reinforced concrete beam to resist service moments of 120 kNm from dead loads and 110 kNm from live loads. The beam dimension are (b x d) 0.25m x 0.6m. Assumefck = 25 N/mm2and fyk = 500 N/mm2.2. Check the design from Q1.3. A reinforced concrete beam is 0.25m x 0.450 m (b x d). The tension reinforcement provided is 2H25 (As = 982mm2). Determine the moment of resistance of the section if fck = 25 N/mm2 and fyk = 500 N/mm2.4. By using the information from Q3, calculate the actual area of reinforcement required.5. Design a rectangular reinforced concrete beam to resist service moments of 195 kNm from dead loads and 145 kNm from live loads. The beam dimension are (b x d) 250 x 500 mm. Assume fck = 30 N/mm2 and fyk = 500 N/mm2. The depth to compresssion reinforcement is 45mm.Take until 2 decimal point for each calculation.
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. a) Determine the depth of compression block, "a".
A simply supported rectangular beam 9 in. wide having an effective depth of 12 in. carries a total factored load of 16.201 kips/ft on a 40 ft clear span. It is reinforced with 10.92 in² of tensile steel, which continues uninterrupted into the supports. If f'c= 3000 psi, fyt= 40,000 psithroughout what part of the beam is web reinforcement required?. Using vertical U stirrups with fyt= 40, 000 psi, design the web reinforcement for the beam,the stirrup spacing and total spacing for the beam.
A beam section is limited to a width of 250mm and a total depth of 550mm. The beam is subjected to a factored moment of 356kN.m. Pc=20.73, fy=346MPa, Pb= 0.027. Use 70mm concrete cover to the centroid of steel reinforcement. Determine the required area of reinforcement for compression in mm?.
11.A beam is to be designed for loads causing a maximum factored shear of 134.2 kN, using concrete with f'c = 35 MPa. Proceeding on the basis that the concrete dimensions will be determined by diagonal tension for a beam in which no web reinforcement is to be used. Determine the appropriate gross depth (mm) of the beam. Let d = 2b. Use db = 20mm and ds = 10 mm. Round up your answer to nearest whole number.
Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
a rectangular beam has a b = 350 mm and d = 400 mm f'c = 26.5 and fy = 414. Use 15 mm for compression reinforcement and 25 bars for tension reinforcement. Calculate the required steel area if the factored moment Mu = 620 kN-m. What is the steel area for tension and compression zone?
A rectangular beam is to carrt a factored moment of 272 kN-m with a width of 250 mm and its effective depth is 450 mm. Using f'c = 20.7 MPa and fy = 344 Mpa: 1. Determine the required number of 25 mm dia. bars in tension reinforcement. 2. Determine the required number of 25 mm dia. bars in compression reinforcement if needed (use d' = 60mm).
A simply supported rectangular beam 14 in. wide having an effective depth of 15.5 in. carries a total factored load of 10.38 kips/ft on a 25 ft clear span. It is reinforced with 6.24 in² of tensile steel, which continues uninterrupted into the supports. If f'c= 3000 psi, fyt= 40.000 psithroughout what part of the beam is web reinforcement required?. Using vertical U stirrups with fyt= 40.000 psi, design the web reinforcement for the beam and the stirrup spacing and total spacing for the beam.
The standard load is 100kN. Given that n=4 and α=1, calculate EALF 80.
Q1- the reinforced flat plate roof slab system that shownin figure. Supports a service live load of 1.5 kN / m2 and a service superimposed dead load of 3.4 kN / m? in addition to its own weight. The slab is supported along its outer edges by a brick wall. Slab thickness is 200mm and wall thickness is 240mm. all interior columns are 300x600 mm. Using the ACI direct design method, design and detail the column strip top bars required at the continuous edges of strip A shown in the plan. Use fe-22 MPa andf-400MP.
A rectangular, tied column 480 mm wide along x-axis and 540 mm wide along y-axis is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 21 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only.