Calculate the pump capacity. 5 m4 m2.5 mCylindrical Tank )Ø= 1.5 iNmust be FilI45mwith in 2 hourseFF = 75%5m3mK- values15 mØ=2 iNElbow - 90°0.45check valve2.5Gate valve0.17Pipe Roughness = 0.0015M = 0.00089 Pa.S= 1000 ka/m

Suction line pipe diameter, ds=2 in=2*0.0254=0.0508 m 1 in=0.0254 mSuction…

Answered: Calculate the pump capacity.

Engineering

Mechanical Engineering

Calculate the pump capacity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 7.52 PLUS Neglecting head losses, determine what power the pump must deliver to produce the flow as…

Q: O2/Detrmin the Reactions and brow , shear fore and bendinel monin Ź Diagrans in He fia. lokN/n

Q: Having the following table and network find the activity with maximum cost slope Activity Normal…

Q: A simple truss is subjected to 20 kN force at point A as shown in Figure 2. The reaction force at…

Q: 8-40 Two parallel 30-cm-diameter disks are separated by a distance of 10 cm and enclosed in a large…

A: Given Diameter, d = 30 cm Temperature, T1 = 1200 K…

Q: 14. 14.5 liters of gas at 172 MN/m2 is expanded at constant pressure until its volume becomes 130.5…

Q: QI: NGO ii - CLO 2 - PI -24 In an epicyclic gear train, an arm carries two gears 1 and 2 having 40…

A: Given T1=40T2=50y=160rpm ccw gear 1 is fixed

Q: What are the importance of Ceramics in Engineering? Give some examples

A: Ceramics : Ceramics are the materials which is inorganic and nonmetallic materials that are…

Q: Compared to individual expansion valves, multiple expansion valves Yield higher refrigeration effect…

A: Soln:- part 1 a) yeild higher refrigeration effect in the low temperature evaporator. Reason - the…

Q: T6 temper designation for an aluminum alloy means: Solution heat treated and artificially aged at…

A: we have to determine what T6 temper designation means for aluinium

Q: O2/De trmin the Reactions and Drow , sheak fore and bendinl moninz Diagrans in te f ia. るm

Q: )The following table is the values of true stress-true strain of killed steel specimen with the…

Q: need the answer quickly

A: Ans: 3. In universal testing machine system, the load is applied on the specimen which gives…

Q: calculate the leakage mass flow rate per unit area from the first ring pack plenum tc the cylinder…

A: Given Temperature, T = 450 K Coefficient of discharge, C = 0.75…

Q: Use modal analysis to calculate the response of the drive train system of Problem 4.44 given by the…

A: Given : To find : Modal analysis

Q: Air at 30 °C and 110 kPa flows at 20 N/s through a rectangular duct that measure 160 mm x 320 mm.…

A: Given data Air temperature = 30°C = 30 + 273 = 303 K Air pressure = 110 kPa Flow rate = 20 N/s…

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

A: According to the details provided in the question, we need to calculate normal stress in the…

Q: A uniform rod AB of mass m = 6.4kg is welded at its midpoint G to a vertical Shaft GD. Knowing that…

Q: 4. A mass m is supported by a spring with stiffness k. The mass is initially at rest at time t = 0.…

A: Given : To find : Time history of spring force

Q: 11. If a sport utility vehicle of mass m corners an unbanked curve with a radius of curvature r at a…

Q: Using area-moment method, determine the maximum displacement of the cantilever beam ABC which has…

A: Answer: The maximum displacement of the cantilever beam ABC: 35 mm

Q: 1. The effect of angle

Q: A container is floating in water. The container has a rectangular shape of 1.52 X 0.66 X 0.50 m (L…

Q: Example 4-6: The water flows through the pipe bend with a discharge of 200Ls. The bend is placed…

Q: I got a solution for this, question is how does he got 2.05 in Kt?

Q: (7-2 from textbook) Determine the specific compressor work input required to compress steam…

Q: 17.3 A self-propelled combine with a four-row 101.6 cm [40 in] corn head has a list price of…

A: Given data List Price= $40,000 Power=91 KW Speed= 6.4 km/hr To determine the average cost per…

Q: 4- Determine the mass of air in a 2 m tank if the air is at room temperature, 25 °C, and the…

Q: Calculate the stress at point B of the cantilever beam shown in Fig. 9.22.

Q: A gusset plate is subjected to the forces shown in the figure below. Find the magnitude (F) And…

Q: Calculate the maximum moment in a 40-foot simply supported beam due to the following axle loads: 24k…

Q: Hydraulics. Derive the formula of Upper not down.

A: In this problem, we have to derive the height of liquid in a spherical container which has a…

Q: In Figure 1, the normal stress on the cross- sectional area is (in Mpa)

A: Inclined force, P=400 kNCross-sectiona area, A=30 mm* 20 mmInclination angle of force P, θ=30o

Q: Q3 // (A) - An element of bone in plane strain where the state of strain are (ex = 8 x 10-4, Ey = 5…

Q: Please answer: How many degrees of freedom are in the system Write out the equations of morion in…

A: For solution refer below images.

Q: An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air…

A: Otto cycle is a type of constant volume heat addition cycle which works in the SI engine. It has…

Q: ı dont understand

Q: ! The solid homogenous 400 lb block A rests on a horizontal plane. The coefficient of friction…

Q: 3- Two cars moving towards cach other, separated by 150 km, If the first car has a speed of 60 m's…

A: The necessary time for them to meet together: t = 25 minutes

Q: I want the third drop 16 60 30 16 115 40 161

Q: motion to a roller follower: raise 50 mm with uniform motion for 120 deg, dwell for 30 deg, return…

Q: If the oscillator in the above problem is released from rest at x = A when the clock is set to t= 0…

A: Given Position x = A when time, t = 0 Find Position and velocity at t = 2 sec Time, t

Q: A pipe with 8 cm intemal diameter, 9 cm outer diameter, 2 meter long, thermal conductivity 30Wimk in…

Q: force at point C is (in kN)

A: To find Reaction force at Point C

Q: Discussion 1. Know vapor pressure. 2. How suit the (Pb) of product with the molecular weight?…

A: Solution is given below:

Q: What are the Advantage & disadvantages, Applications in Industries and control instruments can…

A: Advantages: The advantages of ultraviolet/visible radiation analyzers are given as under.

Q: A straight-charged Thermostatic Expansion Valve (TEV) is designed to operate at an evaporator…

A: INTRODUCTION : We have to determine the appropriate spring pressure for which the saturation…

Q: Problem 1-12 The state of stress at a point is given by : 0, = 40, %3D Oy = 50, 0; = - 70, ty = 40,…

A: The direction cosine after rotation are, x y z x' 3/2 1/2 0 y' -1/2 3/2 0 z' 0 0 1

Q: P.

Q: * liquid limit should always be greater than plastic limit True O False O * Gs is a unitless value…

A: True Liquid limit should always greater than plastic limit As, liquid limit - plastic limit =…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

100%

Calculate the pump capacity.

5 m
4 m
2.5 m
Cylindrical Tank )
Ø= 1.5 iN
must be FilI
45m
with in 2 hours
eFF = 75%
5m
3m
K- values
15 m
Ø=2 iN
Elbow - 90°
0.45
check valve
2.5
Gate valve
0.17
Pipe Roughness = 0.0015
M = 0.00089 Pa.S
= 1000 ka/m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water fl ows through a straight 10-cm-diameter pipe at adiameter Reynolds number of 250,000. If the pipe roughnessis 0.06 mm, what is the approximate Moody frictionfactor?(a) 0.015, (b) 0.017, (c) 0.019, (d) 0.026, (e) 0.032
It is desired to pump ethanol at 20 ° C through 25 m ofstraight smooth tubing under laminar-fl ow conditions,Re d = ρ Vd / μ < 2300. The available pressure drop is10 kPa. ( a ) What is the maximum possible mass fl ow, inkg/h? ( b ) What is the appropriate diameter?
For fl ow of oil [μ = 0.1 kg/(m ? s), SG = 0.9] through along, straight, smooth 5-cm-diameter pipe at 14 m3/h, thepressure drop per meter is approximately(a) 2200 Pa, (b) 2500 Pa, (c) 10,000 Pa, (d) 160 Pa,(e) 2800 Pa
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Q5: What is the diameter of smalle pipe, if the flow rate (30 lit/sec) ? ·S=0.6 D= Ans: 146.8 mm² 40cm D = 200mm D=?
The pipe fl ow in Fig. is driven by pressurized air inthe tank. What gage pressure p1 is needed to provide a 208Cwater flow rate Q = 60 m3/h?
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
The pipe bend of Fig. has D 1 = 27 cm and D 2 =13 cm. When water at 20 ° C fl ows through the pipe at 4000gal/min, p 1 =194 kPa (gage). Compute the torque requiredat point B to hold the bend stationary.
Water at 20°C fl ows at 3 m3/h through a sharp-edged3- cm-diameter orifi ce in a 6-cm-diameter pipe. Estimatethe expected pressure drop across the orifi ce.(a) 440 Pa, (b) 680 Pa, (c) 875 Pa, (d) 1750 Pa, (e) 1870 Pa
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.
Glycerin, sg = 1.26 and μ = 1.49 Pa-s, flows through a 600-mm Ø pipe at 85 liters per second. a. What is the Reynold’s Number? b. What is friction factor? c. What is the critical velocity?
A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 4pa/m as the pressure gradient in all sections. What diameter in ft should be selected in the 5m section? A. 0.54 B. 0.34 C. 1.12 D. 0.44