The physics associated with statics has considerable applications in engineering. As a mechanical engineer working for a tow-truck manufacturer, you have been asked to evaluate the purchase of a new line of towing cable. The supplier claims that,although its cables are not as strong as its competitors (maximum tension capability of 10200 lb), the cost savings make it agood investment.A schematic of the towing configuration is shown. The car weighs 6176 lb, which is as large as the company expects their towtrucks to service. The overall length L of the car is 10.7 ft, and the distance d between the midpoints of the front and back tiresis 9.63 ft. The bottom of the car's frame is a height hf = 0.500 above the ground, and the car's center of mass is a heighthCM = 1.50 above the bottom of the car's frame. The angle ø between the midpoint of the tires and the tow cable is 42.0°.Assume the CM of the car is positioned exactly halfway across its length, the geometry of the wheels and front/rear of the car issymmetrical, and that the coefficient of friction between the road and tires is sufficient to maintain no acceleration in the system.Calculate the tension in the cable just as the front of the car begins to lift off the ground. Assume that the front end rises at aconstant velocity.СМtension:lbBased on your results, what would you advise your company?The cable they are offering is more than adequate. The cost savings make this a worthwhile investment.The cable they are offering is too weak to use. I would decline the purchase.

Thr car is in both rotational equilibrium and translational equilibrium (no acceleration)! Where;…

Calculate the tension in the cable just as the front of the car begins to lift off the ground. Assume that the front end rises at a constant velocity. СМ d- tension: lb Based on your results, what would you advise your company? The cable they are offering is more than adequate. The cost savings make this a worthwhile investment. The cable they are offering is too weak to use. I would decline the purchase.

Calculate the tension in the cable just as the front of the car begins to lift off the ground. Assume that the front end rises at a constant velocity. СМ d- tension: lb Based on your results, what would you advise your company? The cable they are offering is more than adequate. The cost savings make this a worthwhile investment. The cable they are offering is too weak to use. I would decline the purchase.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 118 kg box sits on a flat surface where it has a static friction coefficient of us = 0.524 anda kinetic friction coefficient of Mx = 0.318. What is the minimum horizontal force that a worker mustapply in order to get the box to begin moving?
Two masses mA =9.3kg and mB=6.1kg are on inclines and are connected together by a string as shown in the figure. The angles theta subscript A=700 and theta subscript B = 360 . In the absence of the friction, the force F is required to pull the masses at a constant velocity up the fixed inclines. The force F is now removed. What is the magnitude of the acceleration of the two blocks? Take g =9.81 m/s2, and express your answer using two decimal places.
Consider a pair of forces, one having a magnitude of 20 N and the other a magnitude of 12 N. What maximum net force is possible for these two forces? What is the minimum net force possible?
In the wheelbarrow, the load has a perpendicular lever arm of 7.50 cm, while the hands have a perpendicular lever arm of 1.02 m. (a) What upward force must you exert to support the wheelbarrow and its load if their combined mass is 45.0 kg? (b) What force does the wheelbarrow exert on the ground?
What is the magnitude of the force required to stretch a spring that has a constant of 425 N / m and 215 N / m by 7 cm if they are in parallel?
A force of magnitude 7.50 N pushes three boxes with masses m1=1.30kg ,m2=3.20kg, and m3=4.90kg. Find the magnitude of the contact force between boxes 1 and 2.
A block with a mass m is pushed up an inclined rough surface by a horizontal force F as shown. If the block is being pushed up at a constant speed, find the magnitude of the applied force F, given that theta =35 degrees , m = 5 kg, and the kinetic frictional coefficient between the block and the inclined surface mu_k = 0.2
A mountain climber practices his technique in a mountain climbing school by balancing while suspended by two ropes attached to the ceiling. As shown by the figure, the left rope makes an angle of 60 degrees with the horizontal ceiling and the right rope makes an angle of 30 degrees with the horizontal ceiling. If the right rope has tension T1=322 N, what is the weight of the mountain climber?
A worker pulls a 15-kg crate in a straight line on a level surface by imparting a horizontal tension of 80 N to the free end of a cable whose other end is attached to the crate. If the coefficient of static friction is 0.40, what is the acceleration of the crate?
Draw the FBD of the problem The coefficient of frictionbetween the inner pulley andthe belt is 1/π. Find themaximum value of W that canbe supported without rotatingthe compound pulley P orslipping the belt on thecompound pulley P. Pulley B isfrictionless.
The figure shows a person whose weight is W = 782 N doing push-ups. Find the normal force exerted by the floor on (a) each hand and (b) each foot, assuming that the person holds this position.
Using the same force table that you used, a student was given two forces and asked to find a single force that would produce equilibrium with the two forces. The two forces were given by providing one of the components and the angle the force made with the positive x- axis. The two forces were as follows: Force 1: Fx = −2.70 N; Theta = 220.0 degreees Force 2: Fy = 3.20 N; Theta = 60.0 degrees (a) For each force, calculate the magnitude of the force and the mass required to produce it. (b) Calculate the mass and its angle of application to produce equilibrium with these two forces. Please specify your angle as counterclockwise positive with respect to the positive x-axis.