Calculate the tension T in the cable which supports the (1000+b)lb load with the pulley arrangement shown in figure (2). Each pulley is free to rotate about its bearing and the weights of all parts are small compared with the load. Find the magnitude of the total force in the bearing of pulley C. T 0 = 40 B 1000 +b

Calculate the tension T in the cable which supports the (1000+b)lb load with the pulley arrangement shown in figure (2). Each pulley is free to rotate about its bearing and the weights of all parts are small compared with the load. Find the magnitude of the total force in the bearing of pulley C. T 0 = 40 B 1000 +b

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
Find the vertical force P that will hold the linkage in the position =40. The spring of stiffness k=3kN/m is unstretched when =0. The length of each link is L=200mm. Neglect the weights of the links.
Find expressions for all support reaction Forces in the plane frame with load 3P applied at C as shown in the figure. Joints A and D are pin supported, and there is a roller support at joint F. The lengths and the properties of the members are shown in the figure. Neglect the weights of all members. Select Rfas the redundant.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
A uniform trapdoor shown below is 1.0 m by 1.5 m and weighs 300 N. It is supported by a single hinge (H), and by a light rope tied between the middle of the door and the floor. The door is held at the position shown, where its slab makes a 30° angle with the horizontal floor and the rope makes a 20° angle with the floor. Find the tension in the rope and the force at the hinge.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α = 69 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
Draw the free body diagram for this problem: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom.
The figure shows a bar in equilibrium position resting on the floor at point A and on the wall at point B. If the mass of the bar is m and the angle it makes with the floor is θ = π/6, find the magnitudes of the frictional and normal forces at points A and B.
A boom hinged at the base of a vertical mast is used to lift a 2000 load. Find the tension in the cable and the reaction R the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Show complete solution including FBD.