The two uniform thin Disks Shown in the figure rest on horizontal plane and are connected through Frictionless pin Joints at A & B by a rigid light rod which remains horizontal. disk A is 15kg. -The mass - The mass of disk B is 25kg. The Static coefficients of friction between the plane and discs. A and B are - (Ms) A = 0.2 and (M₂) B = 0.55 At the Instant Shown, a counter clockwise moment T=125Nm is applied to disc B. a

The two uniform thin Disks Shown in the figure rest on horizontal plane and are connected through Frictionless pin Joints at A & B by a rigid light rod which remains horizontal. disk A is 15kg. -The mass - The mass of disk B is 25kg. The Static coefficients of friction between the plane and discs. A and B are - (Ms) A = 0.2 and (M₂) B = 0.55 At the Instant Shown, a counter clockwise moment T=125Nm is applied to disc B. a

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
*********MASS IS 10 KG, NOT LBS********** The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees *********MASS IS 10 KG, NOT LBS********** a)draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, and c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *********MASS IS 10 KG, NOT LBS**********
A cylinder of mass M=500kg has an axle of radius b=1m and a spool of radius R=3m. It is placed upright on a table and the string is pulled with a horizontal force F=750N to the right as shown in the figure. The cylinder is rolling without slipping and the coefficient of static friction between the cylinder and the table is µs =0.34. I = 1/2 MR^2a. Determine the linear velocity of the cylinder when it travels a distance D=2m. c. Determine the linear acceleration of the cylinder. d. Determine the friction force acting on the cylinder. e. What is the maximum pulling force, F, for which the cylinder will roll without slipping.
The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degreesa) identify the type of ensuing motion of the bar,b) draw the free body, kinematic and kinetic diagrams for the bar, c) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, andd) determine the angular acceleration of the bar and the reaction forces at ends A and B.
A garage door is mounted on an overhead rail. The wheels at A and B have rusted so that they do not roll, but rather slide along the track. The coefficient of kinetic friction is 0.55. The distance between the wheels is 2.00 m, and each is 0.50m from the vertical sides of the door. The door is uniform and weighs 850 N. It is pushed to the left at constant speed by a horizontal force F⃗, that is applied as shown in the figure. If the distance h is 1.60 m, what is the vertical component of the force exerted on the wheel A by the track? If the distance h is 1.60 m, what is the vertical component of the force exerted on the wheel B by the track? Find the maximum value hh can have without causing one wheel to leave the track.
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A uniform slender bar AB with a mass of 20 kg and length of 3.6 m leans on a wall as shown. It is attached to a weightless small roller at end A on a smooth horizontal surface. The coefficient kinetic friction between end B and the wall is 0.25. If the bar is released from rest in the position shown when θ is 30°. Then find, determine the normal force at A. determine the normal force at B. determine the frictional force between end B and the wall.
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
The 20 kg symmetrical barrel whose radius is 1m shown in the figure is positioned at rest on the 35 deg. inclined plane by a weight B suspended from a cable wrapped around the barrel. If slipping impends, find B and the coefficient of friction.