Can you calculate the inductance (L) of this coil? inner diameter: 7 mm outer diameter: 18mm height: 7 mm number of turns : 45 wire diameter: 0,70 mm coil color is yellow(Relative magnetic permeability=8 ) if a missing value can you tell me ? thank you. :)

Can you calculate the inductance (L) of this coil? inner diameter: 7 mm outer diameter: 18mm height: 7 mm number of turns : 45 wire diameter: 0,70 mm coil color is yellow(Relative magnetic permeability=8 ) if a missing value can you tell me ? thank you. :)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter16: Inductance In Ac Circuits

Section: Chapter Questions

Problem 5PP: An inductor has a current flow of 3 amperes when connected to a 240-volt, 60-Hz power line. The...

See similar textbooks

Related questions

Q: For safe adequate working space and easy access to service equipment and electrical panelboards, NEC...

A: For safe and adequate working space and easy access to service equipment and electrical panel boards...

Q: Which of the following are/is the majority charge carriers in a Schottky diode? a. Electrons b. Both...

A: A Schottky diode, also known as a hot carrier diode, is a semiconductor diode which has a low forwar...

Q: Q3.Explain how you will install 13 Ampere Switch Socket Outlet (SSO).

A: Q3.Explain how you will install 13 Ampere Switch Socket Outlet (SSO).

Q: what makes instrumentation amplifer have greater CMRR compared to regular difference amplifer?

A: Yes, the instrument amplifier has greater CMRR as compared to the regular differential amplifier, an...

Q: Find the Thevenin voltage.

A: Redraw the circuit and represent the node voltages.

Q: The theoretical maximum efficiency of wind turbines is limited by the velocity of air leaving the tu...

A: It is true that the theoretical maximum efficiency of wind turbines bis limited by the velocity of a...

Q: Two loads A & B,2km and 6km away from substation takes 40 A and 20A respectively. The substation vol...

A: To find the voltage at loading point A.

Q: 2. A 72 slot three phase stator armature is wound for six poles. Using double layer lap coils having...

Q: . Determine the capacitance value that, when placed in parallel with this load, would produce a unit...

A: Given Voltage V=230 V Frequency f=60 Hz When capacitance is placed in parallel with the load which p...

Q: The compressor motor and condenser motor are wired in series or parallel

A: The compressor motor is connected or wired in parallel with the condenser motor.

Q: In the voltage-divider circuit shown in the figure, the no-load value of Vo is 4 V. When the load re...

Q: The voltage applied to a coil having R =200Ω and L = 638 mH is represented by : V = 200 sin( 100πt)....

A: Voltage is given, V=200sin100πt On comparing with standard equation ω=100 rad/s Resistance is given ...

Q: t=0 Lice) 40V Siza 2H at t=6 the switch op ens. Calculate ilt) For t >o

A: ### as per our guidelines if a student posts multiple questions,we are supposed to do the first ques...

Q: Given a sequential logic circuit expression asX(t+1) = p'X+pYY(t+1) = pX'+p'Ywhere X and Y are the t...

A: Consider the given sequential logic circuit expression, Xt+1=p'X+pYYt+1=pX'+p'Y To make the circuit,...

Q: 2. A student measures resistance with a Digital Multimeter. Four 470 Q ±5% resistors are measured. O...

A: Solution: The given Value of the resistance=470±5 % 5 % of 470=470×51005 % of 470=23.5In absolute te...

Q: Why the tranformer rattigs are mentioned in KVA. Discuss in brief.

A: The transformer is a device which is use to transfer the power from one portion to the other withou...

Q: 5) ) The point charge at the bottom of the figure is, Q = 17 nC and the curve is a circular arc, of ...

A: According to Coloumb's law force exerted by one charge on another is directly proportional to produc...

Q: When S3=1, then the data out will be the decimal number D3 D2 D1 1 DO so S1 S2 S3

A: Here the bits d3 d2 d1 d0 are initially connected to logic zero

Q: Find the input impedance of 75-ohm lossless transmission line of length 0.1λ when the load is short...

A: Given: Z0=75 ΩL=0.1λ And the load is short.

Q: 4(A) The transistor in the circuit shown in figure 6 is so biased that the DC collector current Ic i...

Q: Electrical Engineering Question

Q: Per NEC 590.6(A)(3), All 125-volt and 125/250-volt, single-phase, 15-, 20-, and 30-ampere receptacle...

A: The National Electrical Code (NEC) is the most widely adopted Code in the world which is Approved by...

Q: 3) Find from the definition, E { sinw,t}. Use -

A: To find the Fourier transform of sinwt

Q: Please show work

A: Amplifier: An amplifier is an electronic device or circuit which is used to increase the magnitude o...

Q: A coil with a self-inductance of 16 mH and a resistance of 6 Ω is connected to an AC source whose fr...

Q: An oscilloscope is set to 0.5 [V/ cm] vertically and 1 [s / cm) horizontally. Sketch the following t...

Q: The inverse Laplace transform of X(s) is -5 X(s)=- ROC : -3<Re(s)<2 (s- 2)(s+3)

A: Given Laplace transform and its ROC are - Xs=-5s-2s+3ROC: -3<Res<2

Q: Subject Electrical Machine

A: Solution: S.C test: Vsc=48 VISC=6 APsc=200 WK=2400240=10At H.V side so,R01=PscIsc2=20062=5.56 ΩZ01=V...

Q: Find the value of R if the equivalent resistance (Req = 120Ω) of the circuit shown below:

Q: For the network shown below :a. Calculate 5T (T is time constant) .b. Compare 5T to half the period ...

Q: Consider the function as representing the value of an ounce of palladium in U.S. dollars as a functi...

A: Solution: Given: Rt=210+50t3 and t=1 The average rate of change over the time interval [t, t+h] is...

Q: a) Calculate magnetic field (x,y,z component)at P2 and P1 Step 2:Consider both wires b) Now what is ...

A: Given: i1=11 Ai2=11 Al1=6 ml2=11-6 =5 mP10,6,-12P20,6,0P30,6,9 a) When only wire 1 is used: Calcul...

Q: True or False? - Efficiency and capacity factor of an electric power generator depend on how it is o...

A: It is true that the efficiency and capacity factor of an electric power generator depend on how it i...

Q: 7(A) Design an op-amp waveform generating circuit to produce the waveform given in figure 10 below. ...

A: Have to generate square wave signal so, It can be produced by astable multivibrator.

Q: Explain minimum 5 Boolean laws applicable in case of digital circuits.Explain N type semiconductors

A: Law 1: Commutative law A+B=B+A Law 2: De Morgan's law A+B'=A'·B'A·B'=A'+B' Law 3: Complement law A·A...

Q: The transfer function of G(s)= s^2 +s +4/s(s-1)(s+1) is in a closed loop unit negative feedback syst...

Q: For safe adequate working space and easy access to service equipment and electrical panelboards, NEC...

A: The National Electrical Code (NEC) is the most widely adopted Code in the world which is Approved by...

Q: Can i get answer with explanation?

Q: 27) This notch filter is often found in many appliances. This notch filter has a very narrow band re...

A: the frequency at which the amplitude ratio is very low is where the notch filter attenuates more.

Q: 11. Design and sketch the schematic diagram for a non-inverting amplifier with a gain of 10 using a ...

A: NOTE : As per the guideline , will be solving only first question. Please repost the other questions...

Q: Consider the unity-feedback control system with the following feedforward transfer function: G(s) = ...

Q: In Fig., solve for RT, IT, VT, V1, V2, V4, I2, and I3.

Question

Can you calculate the inductance (L) of this coil?

inner diameter: 7 mm

outer diameter: 18mm

height: 7 mm

number of turns : 45

wire diameter: 0,70 mm

coil color is yellow(Relative magnetic permeability=8 )

if a missing value can you tell me ? thank you. :)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain why the lockout relay coil energizes instead of the contactor coil. See Figure 6.34.
An inductor has a current flow of 3 amperes when connected to a 240-volt, 60-Hz power line. The inductor has a wire resistance of 15 . What is the Q of the inductor?
Which of the following capacitors or combination of capacitors could be used to replace an 88-microfarad, 250-volt starting capacitor? 180 microfarad, 250 volt 180 microfarad, 330 volt 150 microfarad, 120 volt 150 microfarad, 250 volt
Two identical coils are wound on a ring-shaped iron core that has a relative permeability of 500. Each coil has 100 turns, and the core dimensions are: cross- sectional area A=3 cm2 and magnetic path length l=20cm. Assume k=0.5. Calculate: a. Mutual inductance b. Total inductance in series if their fields reinforce.
Two identical 900 turn coils A and B lie in parallel plane. A current changing at the rate of 2500 A/s in A induces an emf of 20 V in B. (a) Calculate coefficient of coupling between the two coils (b) If the inductance of each coil is 25mH, calculate the flux produced in coil A per ampere.
A circuit consisting of 20 ohm resistance in series with a coil having 8 ohm resistance and 0.16 inductance is connected to a 220-volt, 50-hertz source. Determine the voltage drop across the coil.
A solenoid coil needs to be manufactured which produces an inductance of at least 2000 Gauss (in SI system = Tesla) when a 10mA current flows through the conductor. Due to space limitations, the coil should be composed of 10 turns over a 1cm length. Do the required calculations and select a core material for the coil from the table below. Your answer will be given over the following series of questions. A. H = 0.12566 oersted B. H = 12.56637 oersted C. H = 1.25664 The relative permeability of the manufactured solenoid from the previous question is: A. μr = 15.916 B. μr = 15915.964 C. μr = 1.2665e10 D. None of the mentioned/ Geen van die genoemde
A solenoid coil needs to be manufactured which produces an inductance of at least 2000 Gauss (in SI system = Tesla) when a 10mA current flows through the conductor. Due to space limitations, the coil should be composed of 10 turns over a 1cm length. Do the required calculations and select a core material for the coil from the table below. Your answer will be given over the following series of questions. A. H = 0.12566 oersted B. H = 12.56637 oersted C. H = 1.25664
i will thumbs up if correct, please help needed (current thriugh the inductor)
Inductance with an air-core toroid with an average radius of 10 mm and a cross-sectional area of 10 mm2 How many turns must be wound to obtain a coil with a value of 0.4 mH? Same inductance value Is a replacement solenoid possible? Please explain.
Calculate the magnetic field in the center of the coil, which has threelayers of 600 turns each, the length of the coil is 0.5 m and circulates a3.2 A current
Two identical air cored solenoids have 200 turns, length of 25 cm and cross-sectional area of 3 sq. cm. Each. The mutual inductance between them is 0.5 uH. Find the self-inductance of each coil and the coefficient of coupling.