CD MUX CD MUX A B DCD 2 C D MUX In the circuit shown in the figure the decoder (DCD) has 2 inputs and 4 (active high) outputs. The 3 multiplexers (MUX) each have 2 select inputs (shown on top of the box) and an active high enable input (shown on the bottom of the box). Inputs A, B, C, D are select inputs, the inputs N through Z are data inputs. If ABCD = 0110, then what will be f.

CD MUX CD MUX A B DCD 2 C D MUX In the circuit shown in the figure the decoder (DCD) has 2 inputs and 4 (active high) outputs. The 3 multiplexers (MUX) each have 2 select inputs (shown on top of the box) and an active high enable input (shown on the bottom of the box). Inputs A, B, C, D are select inputs, the inputs N through Z are data inputs. If ABCD = 0110, then what will be f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a) Explain how a comparator becomesa 1-bit ADC. (b) What is the output when the input voltageisless than, greater than, andequaltothe refence voltage?
21/ The circuit that converts continuous signal into 'n' bit binary number is called as ___________. A) Analog to Digital Convertor B) Encoder C) Digital to Analog Convertor D) Decoder
Implement a full adder using dual 4-input multiplexer Give stb1 and stb2 constant 1. Use ZX to represent output sum and ZY to represent output carry Label the inputs and attach the screenshot for selection pins (1,1) Also mention truth table and block diagram.
Please answer these questions for me to understand our lesson better. Thank you!1. Which IC that outputs 1 when both inputs are 1? 2. What is the output of 7432IC if one of the inputs is 1? 3. Which IC outputs 1 if inputs are complemented? 4. What IC is the complement of an OR gate?
A 12-bit D/A converter has VREF = 5.12 V. What is the output voltage for a binary input code of (101010101010)? What is VLSB? What is the size of the MSB?
What binary number would be produced by an eight-bit A/D converter whose input range is 0 to 10 V and whose input voltage is:(a) 39.3 mV? (b) 4.48 V? (c) 7.81 V?
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
The encoder is the inverse operation of a decoder. It generates the binary code corresponding to the input value. The following figure shows a block diagram of 8-to-3 encoder. There are eight inputs, i.e. D7 through D0, and three outputs (binary code), i.e. B2, B1 and B0. Answer the following questions. (Note: You should show all the steps) 1. If the input D7 is high (or “1”) and the other inputs are low (or “0”), what binary code does the encoder generate? 2. Draw the complete truth table of 8-to-3 encoder.
Multiple Choice QuestionsWhat is true when designing a digital LDO. (a) The clock-driven switching loss is proportional to the number of logic gates connected. (b) Binary search is faster than linear search for any transient stability. (c) Binarysearch requires less D flip flop. (d) High stability at light loads with digital control. (e) The stability of digital control is higher than that of analog control. (f) The size of the MOSFETs used in digital control are the same. (f) The size of the MOSFETs used for digital control is the same.
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Suppose there is a system consisting of temperature sensor, ADC, DAC and a Fan. The temperature sensor gives output as voltage value. As the temperature increases more than 18°C it produces the voltage of 8.17 V. That voltage is then put through a 4-bit Successive Approximation ADC as input. After that the output of that ADC is applied to a 4-bit R/2R- ladder DAC to produce enough voltage to turn ON the fan. Take R=”Group#” KΩ. Consider logic “1” as 7 V and logic “0” as 2V. (i) Illustrate the block diagram for the system showing ADC, DAC, Fan and temperature sensor. (ii) Design the circuit diagram with ADC & DAC for the complete system showing necessary parameters value.
Given a 5-bit ADC with the following reference values Vref= -2V and 12V, what is the voltage represented by the output sequence 01010?