What binary number would be produced by an eight-bit A/D converter whose input range is 0 to 10 V and whose input voltage is: (a) 39.3 mV? (b) 4.48 V? (c) 7.81 V?
Q: he input to a combinational logic circuit is 4-bit binary number (A, B, C, D). Design the circuit…
A: K map for output Y1 is given as, output Y1 = A
Q: Q3: what is the output of the successive-approximation register SAR of the Successive- Approximation…
A: We need to find the output of the successive approximation ADC in which analog input voltage given…
Q: (II) Consider a rather coarse 4-bit analog-to-digital conversion where the maximum voltage is 5.0 V.…
A: Given: Voltage= 5.0 V.
Q: An A/D converter uses 14-bit numbers and has a voltage range between +6V to -6V. ( Use 2 decimal…
A:
Q: Examine the output of the 8 bit DAC converter whose output range is 0 to 12 Volts and whose input…
A: A digital-to-analog converter (DAC, D/A, D2A, or D-to-A) is a system that converts a digital signal…
Q: A 2-bit binary comparator designed by using synchronous state machine has two outputs. The outputs…
A:
Q: 2. Choose between one of these two design problems a) Design a 4-bit synchronous counter which…
A:
Q: N1 C Δt N2 R Delay Delay output or Present state output signal Excitation input or Homework-1: Next…
A: SR NOR Latch :-When using static gates as building blocks, the most fundamental latch is the simple…
Q: What are the values of Aυ, Rin, Rout, and Ai for the common-gate stage shown operating with gm = 0.6…
A: Given gm= 0.6 mS, RI = 50 ohm, R4 = 3 KΩ, RL = 82 KΩ Calculating input resistance of common gate…
Q: 5. What is the function of the digital circuit shown below? Describe its operation briefly and find…
A: Digital Circuits: A digital circuit is created by combining several logic gates on a single…
Q: (1) In a PCM system, SN,R is to be held to minimum of 40dB. Determine the number of required…
A: The solution is given below
Q: Implement the equation F = ab +ac using a multiplexer and logic gates.
A:
Q: Q1. A PCM encoder using A-law has a dynamic range of +2 V. Determine the code word when the input…
A: (a) -120 mV (b) 0.5mV (c) -1.5 V (d) 1.8V PCM encoder using A -law of +2V code word (a) 0110 1001…
Q: In Assembely Language design the ALU that perform the following functionalities: using emu 8086.
A: The Answer :
Q: Design ADC using VTC (Voltage to Time Converter) with clock generator fc=32HZ and the slope of…
A: Given - Clock generator frequency FC=32 Hz. Slope of voltage to time converter K=0.025 Maximum…
Q: Describe a multiplexer from two 8-bit inputs to one 1-bit output using the case-when construction.
A: The solution is given below
Q: 1. How many resistors and switches would be required to implement a 6-bit resistor-string DAC?.
A: As per the guidelines of bartleyby I need to answer only first question.So kindly repost other…
Q: A 10-bit D/A converter has VFS = 5.12 V. What is the output voltage for a binary input code of…
A: Given: 10 bit D/A converter with VFS=5.12 VBinary input=1100010001
Q: Consider sampling (quantizing, digitizing) analog temperatures in the range from -17 to 17 °F. How…
A: Given, Sampling analog temperature in the range from -17 ° F to 17° F. The smallest difference…
Q: 4. If the system requires high-speed operations it would be better to use chips of .. MOS 5. A…
A:
Q: / Design and implement 3-bit binary to gray code converter using PLA
A: To design a 3-bit binary to gray code converter, Let the 3-bit binary inputs be B2, B1, and B0 and…
Q: a. Design 4-bit Parallel in Serial out (PISO) shift register.
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: In the FPGA design flow, Timing based simulation occurs before synthesis Select one: O True O False
A: Given A true or false question based on FPGA design flow. Please find the answer below with…
Q: exponent and, 7-bit mantissa is placed in 1 pit register as shown below. E (4) Which of the…
A:
Q: Please write the RISC-V assembly instructions that create the 32-bit constant Ox23453456 and store…
A: ASSEMBLY LANGUAGE INSTRUCTIONS: ADDI : This instruction modifies the contents of the source register…
Q: For 4.3 V, calculate is the digital output by using a Successive-Approximation ADC method? Also…
A:
Q: What is the simplest equation to describe F(A,B,C,D), where F=1 when the binary value of the inputs…
A:
Q: 2. Find output voltage and current for a binary-weighted resistor DAC of 4 bits with given condition…
A:
Q: naamentals Of Digital Electronics / My courses/EETE2270/ SECTION ASSESSMENTS / Theory Quiz-02 (sec…
A: Need to solve for both question
Q: A 12-bit D/A converter has VREF = 5.12 V. What is the output voltage for a binary input code of…
A: Given binary input code (101010101010)2 Converting given input binary code into decimal code…
Q: 18. a. Draw XOR-XNOR gate outputs respectively by using the input waveforms given below. T1 12 13 T4…
A: The solution is as follows.
Q: Design a 4-bit BCD to Gray Code Converter by using Programmable Array logic.
A: Programmable Array logic done by fixed OR gate and programmable AND gate.
Q: Realize the circuit for 4-bit Binary to Gray converter.
A: In order to convert binary to gray: 1) write the table of binary to gray 2) Draw the k-map for each…
Q: Write the equivalent Logic equation of the circuit Vcc 3 1 24
A: Given gate is OR gate whose output given by Y= w+x
Q: 1. Construct the next-state table based on the state diagram given in Figure 1 and Table 1 2.…
A:
Q: Q: State the differences in transfer operation between 8086 & 8088 MP when executing the instruction…
A:
Q: 2. Design a three-input combinational circuit with the output binary numbers equal to the square of…
A:
Q: Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V…
A:
Q: In a circuit where 4-bit binary input values are applied, design a circuit that makes the output…
A:
Q: (3) A digital system is required to amplify a binary encoded audio signal. The user should be able…
A: Given that, Number of increments = 60. In straight binary, minimum number of bits required to encode…
Q: Q3: How Many channels can be transmitted in same PCM channel, If, the bit rate of this channel is…
A: PCM refers to Pulse Code Modulation, it is used for converting and an analog signal to a digital…
Q: An ammeter havng a measurement range ofo* 15 A is installed to monitor the current of a motor. Ihe…
A: To convert the input value from analog ammeter an analog to digital converter with 4-bit output is…
Q: 1. Suppose that you have a 12-bit, successive approximation register (SAR) A/D converter with a…
A:
Q: 2. Find output voltage and current for a binary-weighted resistor DAC of 4 bits with given condition…
A: the solution is given below
Q: A 3.29-V signal is input to a 12-bit successive approximations converter with an input range of 0 to…
A:
Q: Q1. Using a Finite State Machine, Design a counter that: Count: 000, 010, 111, 011, 110, 100, 001,…
A:
Q: Examine the output of the 8 bit DAC converter whose output range is 0 to 12 Volts and whose input…
A: What is a Digital-to-Analog Converter? A Digital to Analog Converter commonly referred as DAC, D/A…
Q: a. Design a binary counter which counts from (00000101)2 to (00100010)2 using 74x163 ICs and…
A: To find out the binary counter
Q: 1. Designa combinational circuit that will display the BCD value in a 7-segment display (see figure…
A:
What binary number would be produced by an eight-bit A/D converter whose input range is 0 to 10 V and whose input voltage is:
(a) 39.3 mV? (b) 4.48 V? (c) 7.81 V?
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- A 3.29-V signal is input to a 12-bit successive approximations converter with an inputrange of 0 to 10 V and simple binary output. Simulate the successive-approximationsprocess to determine the simple binary output.(II) Consider a rather coarse 4-bit analog-to-digital conversion where the maximum voltage is 5.0 V. (a) What voltage does 1011 represent? (b) What is the 4-bit representation for 2.0 V?A 12-bit D/A converter has VREF = 5.12 V. What is the output voltage for a binary input code of (101010101010)? What is VLSB? What is the size of the MSB?
- (a) Explain how a comparator becomesa 1-bit ADC. (b) What is the output when the input voltageisless than, greater than, andequaltothe refence voltage?A 12-bit D/A converter has a full scale voltage of 10.00 V. What is the voltage corresponding to the LSB? To the MSB? What is the output voltage if the binary input code is equal to (100100100101)?For 4.3 V, calculate is the digital output by using a Successive-Approximation ADC method? Also calculate the error. (10-bit A/D with range 0V – 10V)
- A digital circuit whose number of inputs is 3, how many possible combinations of inputs will it have?21/ The circuit that converts continuous signal into 'n' bit binary number is called as ___________. A) Analog to Digital Convertor B) Encoder C) Digital to Analog Convertor D) DecoderDesign a system called a parallel binary comparator, that compares the 4 – bit binary string A to the 4 – bit binary string B. If the strings are exactly equal, provide a HIGH – level output to drive a warning buzzer.
- A PCM system has the following parameters: a maximum analog input frequency of 4.5kHz, a maximum decoded voltage at the reciever of +-5V, and a minimum dynamic range of 60dB. Determine the following c) actual number of bits used in the PCM code (excluding the sign).A temperature between 51°C and 264 °C is converted into a 0- to 5.0- V signal. This signal is fed to an 8-bit ADC with a 5.0-V reference. What is the actual measurement range of the system? a. What is the resolution? b. What is the maximum quantization error? c. What hex output results from 169 °C? d. What temperature does a hex output of C5H represent?2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?