answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC) * When input is 0000 that means tank is empty. * When input is 1111 that means tank is full. * When input is below 5, that means water level is low. * So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light (by setting an output L to 1) when the water level drops below level 5.

answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC) * When input is 0000 that means tank is empty. * When input is 1111 that means tank is full. * When input is below 5, that means water level is low. * So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light (by setting an output L to 1) when the water level drops below level 5.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Book used is Digital Logic with Verilog Design by Brown & Vranesic. Study the counting circuit diagram below and answer the following questions: a. Based on the circuit drawing, is the Clock Positive-Edge Triggered or Negative-Edge Triggered? b. How was this determination made? c. What are the minimum and maximum valkues of the circuit? Explain. d. There are 3 grayed out boxes we refer to this symbolic use as _____________. Why are these used in circuit design?
.Provide a detailed report on the combinational logic circuits below. 1. Magnitude Comparators a. What are magnitude comparators? b. How does it work? c. Applications of magnitude comparators.
You want to design an arithmetic comparison combined logic circuit. (a) List the steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. With AND, OR, NOT gatesmake it happen. (b)By comparing the numbers 9 and 1 in the circuit you designed, the resultdiscuss.
is it possible to connect the outputs of a comparator to a logic gate (connected to an led)? The led connected to the logic gate lights up if the inputs of the comparator both satisfy a condition, for example, the voltage of both inputs are less than the reference voltages.
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
Behavioural Up Counter With Max Design and implement a 8-bit resetable up count, that stops counting when max is reached. The ports are: module counter( output u8_t count, input u8_t max, input logic clk, reset); The u8_t type is defined in the test bench. count is the counter's output. The counter should increment by one for even positive edge clock until the max is reached. The counter should not increment when max is reached. The counter is reset if reset = 1 when a positive edge clock occurs. The 8-bit comparator module, cmp, must be used to check when max is reached. The test bench will set max to 150 for its testing. Editor // include cmp module module counter( output u8_t count, input u8_t max,input logic clk, reset);logic m_test; cmp test(m_test, count, max); // complete the restendmodule
1:The output of a logic gate is 1 when all the input are at logic 1 and a . OR and EX - NOR Gate b . AND Gate and EX - OR Gate C. OR and EX - OR Gate d . NAND and OR Gate 2: Choose an application of A / D convertor a. Sonar systems b. Radars and Jammers C. Digital Audio apllications d. Encoders 3: Find the simplification of AB + B ( B + C ) + C ( B + C ) a. C + A b. B + C c. 1 d. A + 4: Choose a correct number of input lines for a decoder which has 128 output lines a . 14 b . 7 c . 1 d . 128 6: Select a suitable example for sequential logic circuit . a . Encoder b . None of the given choices c . Counters d . PAL
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
Using a 4-bit signed input P=P3P2P1P0 and a control input Z, use a 4-bit adder and any logicgates to design a digital circuit that does the following: ● Outputs P + 3, if the input Z = 0● Outputs P − 3, if the input Z = 1 You can ignore cases where an overflow* might occur after performing the addition or subtraction operation, as long as the circuit performs the signed binary arithmetic correctly. *In computers, typically there is additional circuitry for an overflow flag that gets triggered when the result of an arithmetic operation “does not fit” the number of bits allocated for the output. Please ensure that your components, such as your 4-bit adder are shown clearly with the complete labels of their input and output pins and signals. The sample diagram below shows examples of these labels.
Act 1 problem solving this is a logic circuits and design laboratory subject please help me with this and screenshot all the solution and answers 2. What is the largest binary number that can be expressed with 16 bits? What are the equivalent decimal and hexadecimal numbers? Answer: 16 bits = ________= _______10 = ______16 3. Represent the decimal number 6,248 in: (a) BCD = (b) excess‐3 code = (c) 2421 code =
Design a counter that counts 1-2-3-5-7 Please explain the following:state diagram state table simplification Logic circuit digital design
State in detail the reason why logic circuits are minimized