ces of wear.

Q: ii) List the benefits of good maintenance? (any three

A: Maintenance is defined as the process of running machine with least possible downtime. Maintenance…

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: mensions a tonnage to E the part if the desity

A: Given compaction pressure = 1000 MPa Surface area of the component = π4652- 202 mm2 We know that Pr…

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: pes o

A: GIVEN: Explain different types of fits?

Q: Define the term 'weight'.

A: Weight is the amount of downward force that is applied by gravity to any object in its gravitational…

Q: Name the four comfort factors.

A: For thermal comfort, below four are the important comfort factors: Temperature Humidity Air quality…

Q: What is the ultimate strength and how can it be determined

A: To Answer :- What is the ultimate strength and how can it be determined.  Answer :-  Strength :-…

Q: bulk modulus of elasticity of oil ?

A: Given: Oil in hydraulic cylinder is compressed from an  volume:  V1=2 m3  V2=1.94 m3Pressure in oil…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: the amoun

A:

Q: Q1:- (a) – Give an explanation for each the following:- 1- The design mistake is very dangerous…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: IS ading edg

A:

Q: layer thickness (in mm)

A: Given; Prandtl no. (Pr)=1T∞=500KLength (L)=1.5  mVelocity of fluid (V)=10 m/sKinectic…

Q: weight percentage

A: Given; Atomic weight of FE =46that of C is=10We have to find weight percentage of carbon in…

Q: a load ir incraasadta

A:

Q: ulties

A: note : according to bartleby guidelines we can solve only first question for you please repost other…

Q: A-The importance, types, co B- International standards re

A: solution  (a) importance of pipelines Transport of raw petroleum, oil based commodities, and…

Q: What is its diameter-to-length ratio for

A:

Q: ease dete- ato

A:

Q: How does the element of material deforms?

A: elements of a material are deformed when some external force is applied to it.

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: the difference between two question ?

A: There are no difference between the two two questions

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: How does the thickness of a material impact the location of points on an FLD/FLC?

A: FLD: forming limit diagram are used in sheet metal forming processes to find the major and the minor…

Q: The minimum possible thickness

A: Given; A thick sheet having 4 mm is rolled with 300 mm diamaterOr, d=300 mm t=4 mmFriction…

Q: The suitable terms for the blanks in the statement ."To change from psig to psia , you must ass…

A: There are many different units of measuring pressure. We can use Pascal(Pa). atmospheric(atm), bar,…

Q: Q3. What is "Hardness" and how it can

A: ◆The hardness is defined as, "the ability of the material that can resist indentation or scratch or…

Q: A ce folla

A:

Q: (EFD),

A: ANSWER- TRUE

Q: List some factors of safety for design of drilled shafts.

A: A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled…

Q: Find the cost for producing the fiftieth unit.

A:

Q: ely. What would be the reading on new scale corresponding to 50°C?

A: Determine the New scale reading corresponding to 50 deg c.

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: What is meant when a metal is said to have goodweldability?

A: Weldability describes the ease with which a metal can be welded properly. The weldability of any…

Q: Why scale D is the correct one?

A: Solution:

Q: How would a small or tight tolerance affect the layout?

A: The lines that are used for locating the points on the objects and items for the purpose of cutting,…

Q: What about the stretch for OA?

A: There is a mistake in the calculation part for TOA.   Consider the three equations (i), (ii), (iii)…

Q: Comparison: Indicate if , or = Better Stiffness: Gold Tungsten

A: Subject : material science

Q: final thickness that can be produced by this

A: Given data;  Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Q: Halp

A: A weld symbol without a flag shows that the weld is to be made within the shop. In more seasoned…

Q: speed rate, deep of cut and measurements of a meat tenderizers

A:

Q: Differentiate enery and force

A: energy is defined as the amount of work that can be performed by force and units of the energy is…

Q: 2. List any four reasons why factor of safety is necessary while choosing the material.

A: The factor of safety is defined in the following two ways: For the ductile materials, the factor of…

Q: maximum possible reduction

A: Given: A thick slab is being cold rolled using roll of: Diameter(d)=600mm R=300 mm Coefficient of…

Q: an internal flaw that would not result in fracture of the tile?

A: option b is the answer.

Q: Q2) ______________________ and ______________________ are two common filing problems that can be…

A: File tools are used mainly for finishing of the material by removing the metals from the surface and…

Corrosion control methods

Corrosion may be defined as the method in which metals are attacked on their exteriors by gases existing in the atmosphere, converting them to their oxides, nitrides, sulfides, etc.