The thickness of a sheet is reduced by rolling (without any change in width) using 600 mmdiameter rolls. Neglect elastic deflection of the rolls and assume that the coefficient of friction atthe roll-workpiece interface is 0.05. The sheet enters the rotating rolls unaided. If the initialsheet thickness is 2 mm, the minimum possible final thickness that can be produced by thisprocess in a single pass is

Given data; Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Answered: final thickness that can be produced by…

Engineering

Mechanical Engineering

final thickness that can be produced by this

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a rolling mill, the rollers can exert a pressure of 219 MPa on the sheet being rolled. If the friction coefficient between the roller and the sheet metal is 0.35 and the flow stress of the steel being rolled is 120 MPa, what diameter rolls would reduce the thickness of 2mm thick sheet by 25% in a single pass?
In a rolling operation using a roll of diameter 1.5 m, if a 35 mm thick plate cannot be reduced to less than 12 mm in a single pass then calculate the coefficient of friction btween the rolls and the plate.
A 300mm thick slab is being cold rolled using roll of 600mm diameter.If the coefficient of friction is 0.08. Determine the maximum possible reduction.
A tube of 12 mm external diameter and 1mm thickness is to be reduced to 16 mm external diameter and 0.5 mm thickness. The die angle is 24º and plug angle is 16º. The coefficients of friction at die and tube interface and tube and plug (mandrel) interface is 0.5. The flow stress of tube material is 340 N/mm2 . The tube drawing is carried at a speed of 0.4 m/s. Calculate the fixed plug
A cold rolling operation is to be used to reduce a 50 mm thick and 200 mm wide copper plate. The entering velocity of the plate is 15 m/min and the exit velocity is 18 m/min. The coefficient of friction is 0.2 and assuming that the reduction in thickness during this process is the maximum draft permissible. If the plate widens by 5% after rolling, calculate the power required to drive the rolls. Assume average flow stress of the material as 180 MPa.
A metal strip is to be rolled from an initial wrought thickness of 3.5 mm to a final rolled thickness of 2.5 mm in a single pass rolling mill having rolls of 250 mm diameter. The strip is 450 mm wide. The average coefficient of friction in the roll gap is 0.08. Taking plane strain low stress of 140 MPa, for the metal and assuming negligible spreading, the roll separating force is.....
A 42mm thick low carbon steel plate is reduced to 34mm in one rolling pass. At the same time that the thickness is reduced, the plate is widened by 4%. The elastic limit of the steel plate is 174MPa and its resistance is 290MPa. The input speed of the plate is 15m/min. The radius of the cylinder is 52.8mm and the rotation speed is 49 revolutions per minute. Determine: a) The minimum coefficient of friction that will make this rolling operation possible. b) The output speed of the plate c) Slide forward
In a sheet metal forming press, the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a. Hydraulic cylinder (bore & length); b. Pump pressure and flow rate; c. Electric motor HP considering 75% pump efficiency; d. Reservoir size; and e. Size of pump inlet and discharge tubing.
A copper strip of 200 mm width and 300 mm thickness is to be rolled to a thickness of 295 mm The roll of radius 300 mm rotates at 100 rpm. The average shear strength of the work material is 180 MPa. Calculate the roll strip contact length and the roll force .
A strip (300x30 mm) is fed through a rolling mill with two powered rolls (each with radius of 300 mm) rotating at the speed of 60 rpm. The flow stress of work material is 90 MPa, and the coefficient of friction between rolls and work is 0.12. For a single rolling operation performed at the contact angle of 6.28°, calculate the followings:a) Work thickness after rolling (in mm)
A solid cylindrical work piece is reduced in height by an open die forging process using flat dies on a mechanical press, powered by a 20 kW motor which operates at 35 strokes per minute with a stroke length of 160 mm. The work piece is 60 mm high and 100 mm in diameter and is to be reduced in height by 15%. The coefficient of friction during the operation is 0,18. Calculate the flow stress of work piece material if the press is set to operate at 90% of its maximum capacity.
Estimate the roll force, F, and the torque for an AISI 1020 carbon-steel strip that is 200 mmwide, 10 mm thick, and rolled to a thickness of 7 mm. The roll radius is 200 mm, and itrotates at 200 rpm. Note that K = 530 MPa and n = 0.26.